Series Body Hardware

Nylon Lock Nut for Shackle Pins 9/16" UNF

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Set of 3 Replacement Rubber Grommets for Series 2a-3 1967-84.Handbrake, Gear, and Transfer Lever.Handbrake has Oval Hole. This set can work for ear...

Shackle Bolt for Front-End of Front Spring and Front-End of Rear Spring 9/16" UNF For 88" and 109"

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.

Bolts, Nuts and Washers for the Bulkhead to the Chassis.Fits Series 1 to 3, 1948-84.

Mounting Pad between Rear Tub Floor and Cross-Braces6 Required for Series 1-3 86"/88" and Defender 90 8 Required for Series 2-3 109" Station Wagon ...

Floor Screws and Spire Nuts. Package of 10x FS-320045 and 10x FS-302532

Spring into action with this shifter spring for 4WD Hi-Low Selector Lever. For Series 1-3 trucks from 1950 through to the end of the run in 1984.

Set of 6 Stainless Steel Door Hinge Pin Kits For Series 2-2a 1958-71. For Two Front and One 2-Hinge Rear Safari Door.

Castle Nut for Halfshaft, Output Shaft and Differential Pinion.Requires Cotter Pin AD-PS608101L and Flat Washer AD-571922.

Shackle Bolt for Rear of Rear Spring - 9/16 UNF 88/107/109

Dust Cap for Wheel Cylinder or Clutch Slave Bleed Screw pn: BB-556508 You are purchasing 1, not 10 like shown in the photo

Starting Handle for Series Engines, (tool for timing) 1948-84.Make certain that your engine has the starting dog on the crankshaft.You might need t...

Spring Clip for Tools behind Front Seats Series 1-3, Extra-Large.Holds tools with a diameter up to 1"; just a little larger than the standard one.Y...

Spring Clip for Tools behind Front Seats Series 1-3.For tools, like the hand crank, with a diameter up to 5/8".You'll need a rivet for installation...

Turnbuckle for Seat Base Locker Lids for Series1-3

Spire Nut for Front Grill Badge, Seat Box and Various Uses.For Series 2-3.

Shackle Bolt for Rear of Front Spring - 9/16" UNF 88/109

Screw for L798 Reverse Lamp.For Late Series 2a and Series 3.2 Required per lamp.

Bolt 1/4" BSF x 1" Lockstop Set Bolt for Swivel Hub S1-3 OEM

Galvanized Stays for Rear Sill/Wings PAIR,In Front of the Rear Tires on Series 2-3, 88 and 109". Left and Right Hand.

Wings to Breakfast Radiator Panel Stud Plate Kit For Series 2-3 Includes 2x BP-MRC5519, 2x BP-MRC5520, 10x M6 Flat Washers, 10x M6 - 80 Flanged Ser...

Pop-Rivet Aluminium. 3/16"x1/2" Maximum Clinch 9/32" Sealed EndPackage of 10

Bolt for Rear Propshaft both ends, and Front Propshaft to Differential.Series 1-3. 8 Required for Rear, 4 Required for Front. For the other Front P...

Stainless Steel Antiluce Pin Kit for TailgateFor Series and Defender.Shiny Pair.

Screw 2BA x 1/2" for Series 2/2a Dash and Various Uses OEM Also for Fuel Cover Plate to Filler Series 2-2a.

Stainless Steel Front Vent Hinge Pin Kit (Set of 4) Notes: For Welded On Hinges. 4 Required per Bulkhead. For Series 2-3 and Most Defenders to 2007...

Set of 3 Replacement Rubber Grommets for Series 2/2a 1958-66. Handbrake, Gear, & Transfer Lever. Note: Handbrake has a Round Hole for Round Sha...

Bonnet Canvas Strip White w/Brass Split Rivets S 2/2a 58-71

Set of 4 Stainless Steel Door Hinge Pin Kits For Series 2-2a Front Doors or Middle Row Doors. Does 4 Hinges.

Nut Spire for Front Wing to Bulkhead Series 2-3, 90/110

Lock Washer Shake-Proof Int Tooth 7/16" for Series 1 Brake Hose & Series 2, 2a, 3 Clutch Hose.

Brake Pipe Clip Stand-Offs Plastic

Rubber Grommet for Brake Line P-Clamps 3/16"-1/4"

P-Clamp for Brake Lines 88/109 Sgl/Dual Line 3/16&1/4"

Automec Small Pipe Bender Tool for 3/16" Copper-Nickel Pipe Great tool for making the right bends when installing any of the 3/16" kits.

Bleed Screw for Wheel Cylinders, Series 1-3 1954-84, and 2/2a Clutch Slave. Note: You are purchasing 1, not 10 like shown in the photo.

Rubber Seal for Fuel Sender UnitFor 109 Station Wagon, Defender Side and Rear Tank to 1998.For the Twist Clamp, see EF-ARA1501L.

Clamp Ring for Fuel Sender For 109 Station Wagon, Defender Side and Rear Tank to 1998. For Rubber Seal, see EF-ARA1502L.

Split Cotter Pin for Tailgate Chain Clevis Pin, Bonnet Prop Rod, or 4WD Selector Lever.Series 1 to 3.Supersedes FS-2389 and FS-3958. 1/16" x 1/2", ...

Clevis Pin for Tailboard Chain.For Series 1-3.This Requires Split Cotter Pin FS-3958L.

Bolt 3/8" BSF x 1 19/32" for Drive Flange Member. These bolt both the front and the rear drive flanges to the hub assemblies. You'll need six per...

Wing Nut for Battery J-Clamp Rod, Air Cleaner Clamp 1/4" BSF Thread. OEM.Note: You are purchasing one.

Front Wings to Bulkhead Fastener Kit.For Series 2, 2a and 3, and Defender.

Nut 3/8" BSF Nylon Self Lock.For Swivel Flange to Axle Bolt, and Rear Stub Axle to the Axle.For Series 1 to 3.

Bolt Kit for Front Stub Axle to Swivel Hub.This is an Axle Set; does both Left and Right Hand Sides.For Series 1-3, 1948-84.

Stainless Steel Bolt Kit for Bonnet Hinges.For Series 3 and Defender.