Best selling products

9" Clutch Plate for 1948-1969 Series 1-2a.For the Clutch Cover/Pressure Plate, see CC-591705.For a Complete Kit with the Cover, Plate and Flywheel ...

Starter Motor for 2.0L, 2.25L & 2.6L Gas Series 1-3, 1954-1984. Replacing 236287 (M418G), 589545, and RTC3854 (2M100).

Coin Tray for Defender Upper Dash 1986-2006,Replacing the Ash Tray,

Rear Corner Trim Panel Galvanized LH Series 2-3

Galvanized Stays for Rear Sill/Wings PAIR,In Front of the Rear Tires on Series 2-3, 88 and 109". Left and Right Hand.

Splash Guard (Mud Shield) for Early Series 2/2a 1958 to April of 1969. Left Hand for Left Hand Drive (Galvanized Steel Sheet). For the RH side, see...

Washer for Half Shaft.Fits the Front and Rear of Series 1-3 10 Spline Axles, (not Series 1 semi-float rear axle). Also for the Transfer Case Output...

Rear Cross-Member Bolt Kit Stainless Steel.Metric, For Series and Defender.To bolt the rear tub to rear body mounting bracket, (Puma style), and to...

Bolt for Drive Flange Member. OEM.For Defender from VIN: LA930456 (1994on), Discovery 1 1992on, and RRC.With LocTite on Ends. For the Flange AD-RUC...

Bolt for Front Propshaft to Transfer Case For Series 1-3. 3/8" x 1-7/32"UNF. 4 Required. For the other Propshaft Bolts, see BN-509045P This Require...

Nut 5/16" BSF for Various Uses. Note: You are purchasing 1, not 5 as shown in the photo.

Stud for Flywheel Housing to Bell Housing and for Starter Motor to Flywheel Housing.Series 1-3, 1956-84 4 Cylinder Engine.Notes:12 Typically Requir...

Horn High Note 12v for Series 1-3, Defender to the end of 1997. With spade connectors, not plugs. For the Low-Tone Horn, see BE-YEB10027 (linked be...

Instrument Panel Rear Cowl for Defender Left Hand Drive with In-Dash Factory AC, up to 2006. Plastic. Typically broken when taking the dash apart. ...

Nut Spire for Front Wing to Bulkhead Series 2-3, 90/110

Brake Caliper Rear Defender 110/130 RH to 1A614447 (roughly 1994-2001). Notes: Uses Solid Rotors, SFP000280 Pads, and DA4105 Kit.

Hand Brake Shoe Retention Kit. Fits Defenders, Discovery 2 and Range Rover P38 from 1993on. 

Spring for Transmission Brake Shoes 1965-Jul/89 (2 Required)

Propshaft, (Drive Shaft), Front for Series 1-3 4 Cylinder 1956-84.Fits Series 1 88" and 109", 1956-58.Fits Series 2-3 88" and 109" 4 Cylinder, (Not...

Delphi PAIR Brake Rotor Rear Solid Defender 110/130 frm XA159807, (from 1999on). This is for both ABS and Non-ABS 110 Rear. Use Brake Pad Fitting K...

NTN Outer Hub Bearing Series 1 Front, Series 2/2A/3 Front and Rear up to 1980. For Inner Hub Bearing see AD-RTC3416G (linked below left) For a comp...

Outer Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Inner Hub Bearing, see AD-RTC3416 (linked below left). For ...

NTN Inner Hub Bearing Series 1 Front, Series 2, 2A and 3, Front and Rear up to 1980. For Outer Hub Bearing see AD-RTC3426G (linked below left) For ...

Foam Gaskets for 3mm Premium Wing Top Protectors. These gaskets sit between the Defender wing and the chequer plate.Fits all Land Rover 90/110's an...

Series 2a-3 88" LHD Dual-Line w/Servo w/oValve NA Std 1969-74.All Pipes in this kit are 3/16" Copper-Nickel with UNF Brass Fittings.Dual Line Syste...

Switch for LT230 Differential Lock and LT77 Reverse Switch Light.Fits Defender 1985-2006, Discovery 1, Discovery 2, Range Rover Classic.This requir...

Gasket Kit for Zenith 361V Carburetor Series 2a-3 from 1968

Rear Cross Member with Extensions - No Spring Hangers For Series 2-3 88" and 109". (88" will require Spring Hangers cut from your original frame or...

Rear Reflector Red for all Series, Bolt-on, 2.25" Diameter.PAIR.

Wipac Deluxe LED Coloured Kit 11 Lamps Euro Style 2-3/4" 73mm Front and Rear Lamps, 4" Rear Fog and Reverse Lamps with Mounting Plynths, and Licens...

Leaf Spring Kit for Series 1-3 86/88" LHD Standard with U-Bolts. Standard Duty Set of Leaf Springs and U-Bolts. *Note: a $40 surcharge for addition...

U-Bolt Set for Front and Rear Leaf Springs, with Lock Nuts.For Series 1-3 86/88", 1954-84.

Locker Plate for Swivel Pin Series 1-2a 1948-1962 3/8" Studs 4 Required per Side, 8 per Axle. You are purchasing 1, not 10 as shown in the photo.

Swivel Pin Bearing - Bottom of Swivel Housing. Series1-3.

Pulley for Alternator on Series 2a/3 Gas or Diesel. Internal Shaft Diameter is 0.59", 15mm. Be sure this fits your Alternator.

Peg for LT76 Gearbox Mainshaft Series 1-3, 1948-84 For the other Peg, see GT-RTC1979 (linked below).