Best selling products

Flanged Bolt M8x20mm for Various Uses

Bolt 1/2" UNF for Bulkhead to Frame.For Series 1 to 3, 1948-84. OEM.Supersedes BN-300827 and BN-303907, (BSF Versions of the same size bolt), no lo...

Timing Chain Kit for Series 2-3 2.25L Gas up to 1974

Hose Clamp 3" - 4" Diameter x 1/2" Bandwidth All Stainless For Various Uses.

Heater Blower Motor Suitable for Smiths Round HeaterFor Series 1 to early 2a.Note: There were many variations of the Smiths Round Heaters; shorteni...

Exhaust Hanger Bracket for Left Exit Tailpipe Series 1-3 86/88" 1954-84 Pre-assembled, ready to bolt into position. Please check your chassis for t...

Castrol Classic Oils Nostalgic Pouring Jug Half Pint

Terrafirma All Terrain Rear Shock with Bushings. Standard Travel Shock. For Defender 90, 110 and 130, Discovery 1 and Range Rover Classic.

Bulkhead Door Pillar Repair Section w Foot-Bracket Right Hand. Series 2-3 and Defender.If replacing a Series 2 to 2a door pillar which has encapsul...

Transmission Hand Brake Expander Unit Series 2A-3, 1961-84. This expander unit requires 3 locking clips to hold it in place (BB-515467/0)

Washer Flat 1/4" ID 1" OD for Floor Panels, Wings & Various

Replacement Footwell Left-Side for Left Hand Drive For Defender 90/110/130 Bulkhead Made in UK

Stainless Steel Brake Hose Set +40mm (1.6") Fits: Defender 90 1984-98

Center Cap LR Black for Alloy Wheels D4, RRL405,RRS,DS. LR Genuine.

Mud Shield for Differential Front or Rear Def/D1/D2/RRC OEM

Bearing for Stub Axle Disco1, RRC 86on, Defender 1993on

Oil Seal Stub Axle Inner Defender from 1994, RRC 92-94, Discovery 1 Fits Defender Front from VA104815 with Front Ventilated Rotors. Rear from LA930...

Stub Axle Kit for Front Defender 90/110/130 from LA (1994) until 2006.

Exhaust Valve Late Series 3, 90/110 2.25 & 2.5L Gas, 5-Bearing Engine.For Inlet Valve see EP-ETC4067 (linked below).

Bolt 1/4" UNF x 11/16" Round Truss Head Slotted.For Floor Panels to Sills and other uses, OEM.Series and Defender.Note: You are purchasing 1, not 1...

Captive Nut for Defender Seatbase, Sill Channel, and other uses. 6mm Nut.Supersedes FS-NK106081.

Hose Clamp 7/16" - 1" Diameter x 9/16" Bandwidth Stainless for Various Uses

Defender Lamp Kit Frt/Rear/Side 300Tdi/TD5 to WA159806

Exhaust Hanger Bracket for Right Exit Tailpipe Series 1-3 86/88" 1954-84 Pre-assembled, ready to bolt into position. Please check your chassis for ...

Exhaust System for Series 1 107/109" 2.0L 1954-58. This kit fits: Series 1, LWB 107" or 109" all Gas or Diesel models 1954 to 1958. Includes Bolts,...

Radiator Cap for 2.0L Diesel and Early 2.25L Gas 10Lbs Pressure Cap. See 2nd photo for difference in size compared to later 9Lbs EC-RTC3610 Cap.

Front Door Sill Panel RH Defender 90/110

Gasket for Clutch Master Cylinder Series 3, 90/110 OEM

Cap for Clutch Release Pivot Pin for R380 TD5 & V8

Clutch Hose Defender TD5, 90/110 V8, D1, RRC V8

Clutch Slave CylinderFor Stage 1 V8, LR 90/110 V8 and Defender V8 NAS, with LT77, LT85, and R380 Gearbox.Supersedes CC-UKC8677 and CC-UKC8677L, (No...

Push Rod for Clutch Slave Cylinder Tdi R380, OEM. For Defender up to Gearbox SN 56A0669086K; Earlier uses CC-FRC3417 (linked below left). After use...

Heavy Duty Clutch Kit, Friction Plate, Cover/Pressure Plate, and Bearing for 200/300Tdi. Pilot or Flywheel Bushing is not included, see GT-LFB50005...

Clutch Pedal Assist Kit Spring and BushingsDefender 1994onReplace the old clutch pedal spring kit to assit the pressing of the clutch pedal on Defe...

Backing Plate for Slave Cylinder Mount S3, 90/110, 101FC

9" Clutch Cover Assembly Pressure Plate, 1948-69 Series 1-2a.For the Clutch Friction Plate, see CC-591704.For a Complete Kit with the Cover, Plate ...

Bracket for Interior Dome Light.For Defender from VIN: MA939976 (1996) OEM.For the Lamp, see LA-AMR3155.

Front Right Hand Wing Outer Panel Aluminium OEM.For Defender 90/110/130 up to 1994.

Edge Clip for Interior Trim and Various - Defender OEM

Clip for Bonnet Prop Rod Solid Defender to WA159806 OEM You are purchasing 1, not 5 as shown in the photo

Striker Pin for Bonnet Catch on Series 2-3, 1958-84Supersedes BP-337969.

Rear Corner Extension Panel for Front of Defender 110 Station Wagon TubLeft Hand, OEM.

Rear Corner Extension Panel for Front of Defender 110 Station Wagon TubRight Hand, OEM

Front Left Hand Wing Outer Panel with Hole Aluminium OEM.For Defender 90/110/130 up to 1994.

Tie Rod End, Set of 6. 3x Right and 3x Left Hand, with Steering Rod Clamp Kits. For Series 1-3 1948-July 74, Unthreaded Shoulders.   Does the Track...

Bonnet Release Lever for Defender from 2A622424

Plastic front rh wing outer panel for Defender with hole. Fits Defender 90/110 from 1998 - 2016.  Replacement for ALR6122 & ASB710260.

Lower Dash Finisher for LHD Defender Land Rover Genuine.Supersedes BP-MTC6167.