Best Selling Products

Differential Pinion (Spyder Gear) Rover Series 1-3 1948-75

Cotter Pin for 24-Spline Series 3 Hubs and 101 Track Rod Ends

Corteco Oil Seal Stub Axle InnerFor Defender from 1994, RRC 1992-94, and Discovery 1

Defender Tailgate Assembly with Hinges, Brackets and Latch Eyes. Has the Cable Retention Brackets. For earlier Series Chain Retention type of Tailg...

Dayco Timing Belt for 2.5NA & 2.5TD

Cylinder Head Bolt for 300Tdi OEM D1/RRC/Defender.Note: You are purchasing 1, not 4 as shown in the photo.

Cylinder Head Bolt for 300Tdi OEM D1/RRC/Defender. Note: You are purchasing 1, not 4 as shown in the photo.

Cylinder Head Complete 300Tdi with Valves and Head Bolts. This head has additional waterways for improved cooling. Use a Multi-Leaf Metal Head Gask...

Crankshaft Damper Pulley for TD5 Defender and Discovery 2 with the TD5Recommended that you also replace the Bolt, EP-LYG101190 (linked below).

Fan Belt for Rover 3.5L V8 w/o AC, w/o PAS

Dayco Belt for A/C Compressor on 300Tdi D1, RRC, Defender

Cup Washer for Instrument Panel to Cowl 90/110. OEM. Note: You are purchasing 1, not 10 as shown in the photo

Detent Spring for Synchronising Clutch, (Clutch Synchro), Assembly in Gearbox. For Series 1 to 3, 1948-84. 3rd and 4th Gear Synchro. Typically 3 Re...

Defrost Demister Vent Dash Top Cover.For Series 3, 1975 to 84.These are 10.75" wide, adaptable for the early Defender vents, (to 1988), HS-MTC6040,...

Demister Hose for Defender 90/110/130 OEM.

Defender - A Celebration of the Best 4 x 4 Vol 2 From the team at Land Rover Monthly, this 228 page magbook celebrates the Defender including vehic...

CV-Joint for Defender 1994 - 2006, Discovery 1 w/ABS, RRC 1992 onwards. 24 splines to the drive flange, 32 splines towards the driveshaft

Clutch Slave Cylinder for Defender and Discovery 2.300Tdi from Gearbox 56A0669087K (1999)TD5 up to 2007

Clutch Plate Standard Duty Defender 2.5NA, 2.5TD, 200Tdi and 300Tdi.

Clutch Slave Repair Kit RRC 70-94, D1 89-94, 90/110, LT77

Connecting Tube for Clutch Throw Out Cross Shaft.For Series 2 to 2a.

Clip for Clutch Release Throw-Out Lever S3, Def, RRCto'94, D1

Clutch Release Fork for LT77 and R380 4 Cylinder, OEMIncludes the little bits shown in the photo, which you should replace when replacing the clutc...

Complete Floor Bolt Kit for Series 1 1954-58 86/88/107/109"

Clutch Pedal Pivot Bushing on the Clutch Pedal Spring, CC-EDP7510L (linked below).For Defender 1994 onwards.

Clip 1/4-Turn Screw Type for Disco2, LR3/4, RRS06-09

Connecting Rod Bolt for most 2.5L Engines upto 1998 (300Tdi) OEM Note: You are purchasing 1, not 4 as shown in the photo.

Connecting Rod Nut for most 2.5L Engines upto 1998 (300Tdi) OEM

Connecting Rod Big End Bearing Set .020 US 2.25L Gas/Diesel 1961-84.For Series 2a to 3.Note: Does not fit the Series 2 (1958-61) Engine.

Connecting Rod Big End Bearing Set .020 Thou Over.For 2.5L Naturally Aspirated Diesel, 2.5L Turbo Diesel, 200Tdi, and 300Tdi.OEM King.

Connecting Rod "Big End" Bearing Set .010 US.1955-58 Series 1 2.0L Spreadbore Engine.New Old Stock.

Connecting Rod Bearing Set .040 US.Series 1 1955-58 2.0L Gas Spreadbore Engine.New Old Stock.

Clip for Clevis Pin Various Uses, Gearbox, Handbrake, LT230

Clip for Clevis Pin LT230 Transfer Lever upto LA939975 OEM

Clip for Diff Lock Link LT230 Transfer Case OEM

Clevis Pin for LT230 Transfer Linkage, Defender Door Check Straps, and Various Uses OEM Note: You are purchasing 1, not 10 as shown in the photo