Best Selling Products

Rubber Seal for Gearbox Selector Detent Spring 48-84

Replacement Headlamp Retaining Ring with Black Bezel.Includes the retaining bezel, mounting ring, clips, screws and 2 adjuster screws.For Defender ...

Push-Button Starter Switch Series 1-2a, 1948-1966. Note: This Does Not include the Knob. Use your original, or see BE-605280 (linked below). Supers...

Radiator Top Hose Series 2 and Early 2A. 1958-1968. Petrol and diesel.

Oil Pan Sump Drain Plug for TD5. For Defender or Discovery 2 with the TD5 Engine. Requires copper washer CS-CDU1001L (linked below).

P-Clamp for Brake Lines.For Series 1-3 Single or Dual Line 3/16 and 1/4" Pipes.Supersedes BC-50640.

Nut 1/4" BSF for Various Uses. For the Swivel Lock stop Bott, Yellow 4WD Knob, 4WD Clevis Assembly, Transfer Case Bottom Cover, Series 1 2.0L Intak...

The good old standard lug nut. This is a 16mm wheel nut (metric, my American friends). Fits the Series 3 from 1971 through 1984, Defender, and Di...

Lucas L841 Rubber Base for Side Marker Lamp.For Late Series 2a and Series 3 North American Standard.

Rebuild Kit for CB-Type Master Cylinder BB-520849.For Series 2 and Early 2A 88" Short Wheel Base.

Brake Shoes Axle Set 10" Front or Rear. OEM, Mintex.Fits Series 1 80", 86", and 107" Front with 10" Brakes.Series 2-3 88" Front up to June 1980.Ser...

Interior Lamp Metal with Glass Lens. Series 1-3 1956-84. Defender to VIN LA939975, (1995). For later Defender Switched Lamp, see LA-AMR3155 (linked...

Gasket Paper for Oil Sump, aka Oil Pan GasketFor 4 cylinder 2.25L and 2.5L Gas, 2.0L and 2.25L Diesel.Supersedes EG-247088G.

Exhaust Manifold Stud Kit (3 Studs, locks, & brass nuts) 2.25L Gas 61-84 For Mounting Down Pipe to Manifold. (These are included in the Comple...

Front Spring Shackle Plate Threaded 9/16" UNF.Inner Shackle for Series 2a-3, 88" and 109", From March 1963, Suffix B on.

This is a rubberized end cap for the Defender's front bumper.Fits either side on the standard bumper starting in 1984 all the way through the end o...

Exhaust Hanger Bracket Kit (3 Brackets) for Left Exit System 86/88" 1954-84 Pre-assembled, ready to bolt into position. Please check your chassis f...

Collar for Front Axle Bearing on Half shaft Series 1-3 OEM 1948-84.

Copper-Nickel Pipe, (will not rust), with Brass Fittings for use on;Series 2 and 2a, 1958 to 1971 with separate Brake/Clutch Reservoir Canister.1/...

Clutch Release Bearing Series 1 to 2A, 1948-71Used for both 9" and 9-1/2" Clutch. 2.25L and 2.6L NADA.Also used on Front Output of LT230 for Defend...

Service Kit for Series 2A/3 - 1964 onwards with Lucas 25D distributor with fixed points Will not fit vehicles fitted with a Ducellier distributor...

Bulb 12v for Stop/Tail LampFits Series, Defender, Discovery 1, Discovery 2, RRC, and RR P38

9.5" Clutch Plate Optional 1964-71, Standard 1970-84 Late 2A, Series 3 Optional 9.5" Clutch used on NADA Gas/Dsl 88 and 109, 1964-71. Standard on D...

2.25L 4 Cylinder Ignition Lead Set- OEM Lucas Series 2a, 3, 1970-84.Shorter Ignition Coil to Distributor Wire, for Coil located on Right Hand side ...