Best Selling Products

Brake Drum 10" Series 1 to 2A 1948-1969. 80", 86", and 88" Front and Rear. Series 1 107" with 10" Brakes.Note: Holes are 0.581", (a bit larger than...

Tie Rod End for Steering Track Rod, Drag Link or Longitudinal Tube.Left Hand Thread, Series 1-3 1948-July 74, Unthreaded Shoulder.See 2nd Photo for...

Swivel Hub Oil Seal, The large seal for the front swivel balls.For Series 1-3, 1948-1984.For a Kit with the Seal Retainer and Correct Bolts and Nut...

Screw for Fastening Speedometer Cable to Gearbox2BA x 1/4". Series 1-3. Typically 3 Required. You may need the Lock Washer, FS-WM702001L.NOTE: You ...

Radiator Cap for Series 2a-3 9lb Pressure Gas/Diesel. Includes Rubber Seal. Not for Series 1, Series 2 or Early Series 2a. See EC-217437 for Series...

Hylomar Universal Blue Gasket/Jointing Compound 100g Non-Setting Joint Compound.

Hardtop Seal, Windscreen/Windshield to Hard Top.For Series 2-3 1958-1984, Regular, Station Wagon and Pick-Up Truck Cab Roofs. For the Windscreen to...

Gasket for Stub Axle to Swivel Hub Front, Series 1 to 3, 1954-84

Chassis Bump Stop Buffer Series 1-3 with Bolts and Nuts.

Master Brake Cylinder CB Type.For 88" Short Wheel Base Series 2 and Early 2A, 1958-67, (Single Line System Without Brake Servo).

Brake Kit Front Axle Set, 4 Cylinder, 86/88", 10" Brakes, up to June '80, Kit includes; 1x STC2796 10" brake shoes axle set 1x 243296 right wheel c...

Thermostat Housing Gasket Rear Housing to Bypass,Series 2a to 3, 1961 Onwards.

Shackle Bolt for Front-End of Front Spring and Front-End of Rear Spring 9/16" UNF For 88" and 109"

Rubber Glazing Seal for Windscreen Defender 90/110

Corteco OEM Hub Oil SealFits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full float axles f...

Brake Light Switch, Hydraulic Pressure on Pipe UnionSeries 2 and 2aNote that this Switch has 1/8"NPTx27TPI and must be used on the 5-way union foun...

Clutch Alignment Tool Series 1-3 for 9" & 9.5" Clutch Plates

Voltage Regulator for Instrument Panel Series 2-3 1961-84

Tie Rod End, Set of 4.2x Right and 2x Left Hand, with Steering Rod Clamp Kits.For Series 1-3 1948-July 74, Unthreaded Shoulders.

Tie Rod End for Steering Track Rod, Drag Link or Longitudinal Tube.Right Hand Thread, Series 1-3 1948-July 74, Unthreaded Shoulder.See 2nd Photo fo...

Rubber Buffer between Bulkhead and the Bonnet.For Series 2-3 and Defender up to VIN: LA939975, (1994).See BG-MRC6270 for Under Bonnet Buffer (Defen...

Radiator Hose Kit for Series 2 and 2A 1958-68 With Stainless Steel Hose Clamps. Not for use with Later Series 2a/3 Replacement Radiator; see EC-H...

Oil Filter Long Early Type 6.8" Long by 3.75" Diameter.For Series 2-2a, 1958-1964 with Seal.Supersedes ES-248863.

Land Rovers were a crucial vehicle for the RAF Mountain Rescue Service and are the inspiration for this long sleeve heavy cotton shirt. The ‘Series...

License Plate Light Assembly Series 2-3, Defender (Some S1)

Lock Cylinder and Keys, Ignition Series 1-2a Gas 1948-71 Series 3 and Defender without Steering Column Lock. Also used on Series 3 Anti-Burst Door ...

Hinge Bushing for Hood (Bonnet),For Series 2a-3, 1972 on, Defender through to 2016,

Gasket Kit with Seals for Transfer Case LT230For Defender, Discovery 1, and RRC. OEM.

Floor Screws and Spire Nuts. Package of 10x FS-320045 and 10x FS-302532

Delphi AP Brake Pad Set Front. Defender 110 and 130 1986 onward. Defender 90 with Solid Rotors from 1991 to 2016. Defender 90 with Vented Rotors fr...

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.

Front or Rear Brake or Clutch Hose, 86/88 107/109, 3/8" UNF.For use on:Series 1 to 2a, Front Brake, Left or Right, 86/88" SWB or 107/109" LWB, fro...

Bolts, Nuts and Washers for the Bulkhead to the Chassis.Fits Series 1 to 3, 1948-84.

Escutcheon for Door Sill ButtonFor Defender 1987on, and Range Rover Classic from VIN: FA351847 1989on.For a Complete Kit of all 3 Parts, see DP-DA2...

Lucas Classic Sports Coil.For 2.25/2.5L 4 Cylinder Engines, Series and Defender.

Intake to Exhaust Manifold Stud Kit (Studs, Locks, Nuts, and Gasket),For Mounting the Intake Manifold to the Exhaust Manifold on Series 2-3 Gas Eng...