Best Selling Products

Detent Spring for Synchronising Clutch, (Clutch Synchro), Assembly in Gearbox. For Series 1 to 3, 1948-84. 3rd and 4th Gear Synchro. Typically 3 Re...

Defrost Demister Vent Dash Top Cover.For Series 3, 1975 to 84.These are 10.75" wide, adaptable for the early Defender vents, (to 1988), HS-MTC6040,...

Demister Hose for Defender 90/110/130 OEM.

Defender - A Celebration of the Best 4 x 4 Vol 2 From the team at Land Rover Monthly, this 228 page magbook celebrates the Defender including vehic...

CV-Joint for Defender 1994 - 2006, Discovery 1 w/ABS, RRC 1992 onwards. 24 splines to the drive flange, 32 splines towards the driveshaft

Clutch Slave Cylinder for Defender and Discovery 2.300Tdi from Gearbox 56A0669087K (1999)TD5 up to 2007

Clutch Plate Standard Duty Defender 2.5NA, 2.5TD, 200Tdi and 300Tdi.

Clutch Slave Repair Kit RRC 70-94, D1 89-94, 90/110, LT77

Connecting Tube for Clutch Throw Out Cross Shaft.For Series 2 to 2a.

Clip for Clutch Release Throw-Out Lever S3, Def, RRCto'94, D1

Clutch Release Fork for LT77 and R380 4 Cylinder, OEMIncludes the little bits shown in the photo, which you should replace when replacing the clutc...

Complete Floor Bolt Kit for Series 1 1954-58 86/88/107/109"

Clutch Pedal Pivot Bushing on the Clutch Pedal Spring, CC-EDP7510L (linked below).For Defender 1994 onwards.

Clip 1/4-Turn Screw Type for Disco2, LR3/4, RRS06-09

Connecting Rod Bolt for most 2.5L Engines upto 1998 (300Tdi) OEM Note: You are purchasing 1, not 4 as shown in the photo.

Connecting Rod Nut for most 2.5L Engines upto 1998 (300Tdi) OEM

Connecting Rod Big End Bearing Set .020 US 2.25L Gas/Diesel 1961-84.For Series 2a to 3.Note: Does not fit the Series 2 (1958-61) Engine.

Connecting Rod Big End Bearing Set .020 Thou Over.For 2.5L Naturally Aspirated Diesel, 2.5L Turbo Diesel, 200Tdi, and 300Tdi.OEM King.

Connecting Rod "Big End" Bearing Set .010 US.1955-58 Series 1 2.0L Spreadbore Engine.New Old Stock.

Connecting Rod Bearing Set .040 US.Series 1 1955-58 2.0L Gas Spreadbore Engine.New Old Stock.

Clip for Clevis Pin Various Uses, Gearbox, Handbrake, LT230

Clip for Clevis Pin LT230 Transfer Lever upto LA939975 OEM

Clip for Diff Lock Link LT230 Transfer Case OEM

Clevis Pin for LT230 Transfer Linkage, Defender Door Check Straps, and Various Uses OEM Note: You are purchasing 1, not 10 as shown in the photo

Control Cable for Heater Outlet Main Air Valve. Actuated when turning on the Blower.For Defender to VIN: 2A633474, 2002.For later see HS-JFF000140 ...

Complete Front Wiper Arm/Blade Kit for Defender LHD 1983-01.Includes 2 Wiper Arms, 2 Sprung Blades, 2 Adapters for Wiper Arms, and a Hex Key for th...

Exhaust System for Series 1 107/109" 2.0L 1954-58. Right Exit Tailpipe. This kit fits: Series 1, LWB 107" or 109" all Gas or Diesel models 1954 to ...

Clutch Release Bearing. Series 3, 71-84, Defender, Range Rover Classic, Discovery 1,

Series 2a-3 109" LHD Dual-Line w/Valve 1970-80 All Pipes in this kit are 3/16" Copper-Nickel with UNF Brass Fittings. Dual Line System with Propo...

Series 2 88" LHD 1958-1961All Pipes in this kit are 3/16" Copper-Nickel with UNF Brass Fittings.Includes Plastic Pipe Stand-Offs, (PN: BC-CRC1250L)...

Complete Service Kit Ducellier Ignition Some Series 3's.Includes; ES-RTC3184 Oil Filter, EF-606168 Fuel Filter (in-line), 4x EE-RTC3570 Spark Plugs...

Complete Service Kit Lucas Sliding Points Late Series 3.Includes; ES-RTC3184 Oil Filter, EF-606168 Fuel Filter (in-line), 4x EE-RTC3570 Spark Plugs...

One Check Strap for 109 1-Ton or with Salisbury AxleFor a Pair see CP-CHKSTP109X.

Carburetor Linkage Ball Joint for Series 1 Solex 32PBI 1948-58Note: 1/4" BSF Male and 1/4" BSF Female ends.Requires BN-3819 1/4" BSF Nut for Lockin...

Cap for Pivot on Clutch Release on Series 3

Catch Assembly RH Cab Rear Window and Hard Top Sides

Catch Assembly Latch LH Cab Rear Window and Hard Top Sides

Center Catch for Seat Base Lids 90/110 and Various OEM

Check Strap Bracket Front Door Series 3, 90/110 Rear 82-89

Bulkhead Repair Panel with Vent Left Hand Series 2-3 and Defender Note: Fitting to Series Bulkheads may require slight modifications.

Caliper Guide Pin Kit for Front (Axle Set) on D2, RR P38

Bushing for ABS Sensor Def, D1, D2, RRC, P38

Clevis Fork End for Hand Brake Link on Series 2 to 3, and on the Clutch Slave for Series 2 to 2a.Note this is threaded 5/16" UNF. It needs Pin BB-2...

Circlip for Inner Axle to CV-Joint 90/110 to KA930455, (1993).Land Rover Genuine Part.

Clamp for Spare Wheel on Bonnet 3/8" Hole,This only works with the original 3/8" Bolt 301274 - Call us if required.

Circlip for Primary Pinion in Gearbox S3, Clutch Withdrawal 48-50

Bush Gear Box Selector - 4WD 1951-84 OEM

Castle Nut for Front of Layshaft Series 2a 1964-71 3/4" UNF