Defender Hardware

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Everything you need to affix your door cards properly to your door.This kit does one door, either front, or middle, not the rear safari doors.That'...

Hinge Bushing for Hood (Bonnet),For Series 2a-3, 1972 on, Defender through to 2016,

Castle Nut for Halfshaft, Output Shaft and Differential Pinion.Requires Cotter Pin AD-PS608101L and Flat Washer AD-571922.

Mounting Pad between Rear Tub Floor and Cross-Braces6 Required for Series 1-3 86"/88" and Defender 90 8 Required for Series 2-3 109" Station Wagon ...

Rubber Seal for Fuel Sender UnitFor 109 Station Wagon, Defender Side and Rear Tank to 1998.For the Twist Clamp, see EF-ARA1501L.

Clamp Ring for Fuel Sender For 109 Station Wagon, Defender Side and Rear Tank to 1998. For Rubber Seal, see EF-ARA1502L (linked below).

Bolt for Caliper M12 x 35mm.Fits Defender Front and Rear, Discovery 1, Discovery 2, RRC, and RR-P38.Check your application before ordering.Supersed...

Staple for Hood Strap on Rear Tub and on Windscreen Rail.For Series and Defender.You are Purchasing 1, not 10 as shown in photo.

Stainless Steel Front Vent Hinge Pin Kit (Set of 4) Notes: For Welded On Hinges. 4 Required per Bulkhead. For Series 2-3 and Most Defenders to 2007...

These are the fasteners necessary for fitting the bumper end caps (CP-DPT100070) on the Defender. You'll need four per cap, so eight in total. The...

Bolt Kit Rear Suspension Trailing Arms and A-Frame Bolts.For Defender up to VIN: 9Axxxxxx (2009), Discovery 1, and RRC. For Imperial Bushings.For l...

Stainless Steel Antiluce Pin Kit for TailgateFor Series and Defender.Shiny Pair.

Plastic Nail Trim Clip for Dash Panel Defender. OEM.Note: You are Purchasing 1, not 10 as shown.

Key Blank Ignition Defender 1987-2017.All Defenders with Steering Column Lock.Aftermarket.Supersedes KB-STC4798, KB-AAU8276.

Hinge to Door Screw 2" Long for Series 3 and Defender Hinges up to 2006, OEM This is the longer screw that holds the Hinge to the Door. For the sho...

Captive Nut Door Hinge to BulkheadFor Series 3 and Defender up to 1998, and earlier bulkheads repaired with New Door Posts.OEM. These are UNF Threa...

Defender Bumper Stainless Steel Bolt Kit with Tap Blocks and Black Caps.

Battery Hold-Down J-Clamp Kit

Stainless Steel Bolt Kit for Bonnet Hinges.For Series 3 and Defender.

Floor Screw Acme Thread Series 1-3 and DefenderFor a Package of 10 Floor Screws see FS-320045-10 (linked below left), or a Package of 10 Screws and...

Propshaft Bolt and Nut Kit for Front PropshaftFor Defender, Discovery 1, RRC, RR P38.

Propshaft Bolt and Nut Kit For One Rear PropshaftFor Defender, Discovery 1, RRC,and RR P38.

Pop-Rivet Aluminium. 3/16"x1/2" Maximum Clinch 9/32" Sealed EndPackage of 10

Set of 12 Cylinder Head Bolts for TD5 Engine. Defender and Discovery 2 with TD5 Engine. For a Head Gasket Sets, see EG-DA2112G-EARLY or EG-DA2112G-...

Stainless Steel Screw Set for Side Air Intake Defender Set 5For Side Air Intake BP-BTR6188For replacement Captive Nuts in Wing Panel see FS-AFU1926L

Strap for Windscreen Inner Hinge Mount Defender Note: From JA912346 (1992). For earlier see BP-RTC6159.Supersedes: BP-MUC4290, BP-LR016671

Headliner Fir Tree Fasteners Light Grey Various UsesDefender, Discovery 2, RR P38

Striker for Anti-Burst Door Handle Defender 90/110/130 from AA270227(1987). OEMAll Front and Middle-Row Doors. Not for the Rear Safari Door.

Spire Nuts for Floor Screws and Other Uses Package of 10

Bolt for Front Panhard Rod 90/110 OEM (2 required) Note: You are purchasing 1, not 5 as shown in the photo.

Nut Spire for Front Wing to Bulkhead Series 2-3, 90/110

Bolt ACME for Front Wing to Bulkhead S 2-3, 90/110 Zinc. OEM.

Hinge Gasket for Door Hinge to Bulkhead Series 3 Def to 1997

Hinge to Bulkhead Screw 1.5" Long for Series 3 and Defender Hinge, OEMThis is the shorter screw that holds the Hinge to the Bulkhead. For the longe...