Aftermarket

Set of 3 Replacement Rubber Grommets for Series 2a-3 1967-84.Handbrake, Gear, and Transfer Lever.Handbrake has Oval Hole. This set can work for ear...

Gearbox and Transfer Case Gasket Set - Series 1-3 1948-84

Door Top Rubber Seal (Between Door and Door Top) Series 2-3

Front Chassis Bushing for the Rear of the Front Spring. This goes through the Chassis Rail for the Front Spring's rear shackle assembly.For Series ...

Oil Seal for End of Front Axle Casing 1948-1984 Series 1-3

Hub Bearing and Oil Seal Repair Kit. Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully Floating Axles on 109", and 88" with the optional full ...

Distance Piece Collar for Stub Shaft Front or Rear Axle Race for Hub Seal. OEM. Series 1-3 upto 1980 Series 1 Front Only up to 1956.

Rebuild Kit for Clutch or Brake Master Cylinder.For CV-Type 88" Master Cylinder 90569126, (Used as a Brake Master Cylinder on Series 2/2a 88" Singl...

Slotted Drain Plug Tool for Series, Defender, and RRC.Uses a 19mm or 3/4" Socket or Wrench.For use on the Slotted Drain Plug, AF-235592.So much eas...

Lock Nut for Hub Bearing Front or Rear.For Series 1-3, Defender, Discovery 1 and RRC, from 1948 through to 1998.OEM Quality.Supersedes AD-217355, A...

Hardtop Seal, Windscreen/Windshield to Hard Top.For Series 2-3 1958-1984, Regular, Station Wagon and Pick-Up Truck Cab Roofs. For the Windscreen to...

Front Crankshaft Oil Seal Corteco OEM Fits, Series 1, 1.6 and 2.0L Series 2, 2a, and 3, 2.25L 4Cyl and 2.6L 6Cyl Defender, Discovery 1 and RRC, 2.5...

Corteco Pinion Oil Seal Rover Differential Front or Rear.For Series 1-3 1950-84Supersedes AF-217507, AF-561360.

Chassis Bump Stop Buffer Series 1-3 with Bolts and Nuts.

Tie Rod End for Steering Track Rod, Drag Link or Longitudinal Tube.Left Hand Thread, Series 1-3 1948-July 74, Unthreaded Shoulder.See 2nd Photo for...

Swivel Hub Oil Seal, The large seal for the front swivel balls.For Series 1-3, 1948-1984.For a Kit with the Seal Retainer and Correct Bolts and Nut...

Screw for Fastening Speedometer Cable to Gearbox2BA x 1/4". Series 1-3. Typically 3 Required. You may need the Lock Washer, FS-WM702001L.NOTE: You ...

Hylomar Universal Blue Gasket/Jointing Compound 100g Non-Setting Joint Compound.

Corteco OEM Hub Oil SealFits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full float axles f...

Master Brake Cylinder CB Type.For 88" Short Wheel Base Series 2 and Early 2A, 1958-67, (Single Line System Without Brake Servo).

Brake Drum 10" Series 1 to 2A 1948-1969. 80", 86", and 88" Front and Rear. Series 1 107" with 10" Brakes.Note: Holes are 0.581", (a bit larger than...

Thermostat Housing Gasket Rear Housing to Bypass,Series 2a to 3, 1961 Onwards.

Shackle Bolt for Front-End of Front Spring and Front-End of Rear Spring 9/16" UNF For 88" and 109"

Rubber Glazing Seal for Windscreen Defender 90/110

Rubber Buffer between Bulkhead and the Bonnet.For Series 2-3 and Defender up to VIN: LA939975, (1994).See BG-MRC6270 for Under Bonnet Buffer (Defen...

Gasket for Stub Axle to Swivel Hub Front, Series 1 to 3, 1954-84

Clutch Alignment Tool Series 1-3 for 9" & 9.5" Clutch Plates

Brake Kit Front Axle Set, 4 Cylinder, 86/88", 10" Brakes, up to June '80, Kit includes; 1x STC2796 10" brake shoes axle set 1x 243296 right wheel c...

Tie Rod End for Steering Track Rod, Drag Link or Longitudinal Tube.Right Hand Thread, Series 1-3 1948-July 74, Unthreaded Shoulder.See 2nd Photo fo...

Intake to Exhaust Manifold Stud Kit (Studs, Locks, Nuts, and Gasket),For Mounting the Intake Manifold to the Exhaust Manifold on Series 2-3 Gas Eng...

Radiator Cap for Series 2a-3 9lb Pressure Gas/Diesel. Includes Rubber Seal. Not for Series 1, Series 2 or Early Series 2a. See EC-217437 for Series...

Oil Filter Long Early Type 6.8" Long by 3.75" Diameter.For Series 2-2a, 1958-1964 with Seal.Supersedes ES-248863.

Nut 3/8" UNF Nylon Self-Locking for PropShaft and Other uses.

Mahle Oil Filter for Defender TD5 and Discovery 2 TD5 Engines.

Lucas OEM Indicator Switch Horn, Dim, and Headlight Dip Defender from VIN VA104806, 1997-2014 For Earlier see BE-STC439 (linked below).

Hinge Bushing for Hood (Bonnet),For Series 2a-3, 1972 on, Defender through to 2016,

Gasket Set for Top Overhaul 4cyl 2.25L Gas with Composite Head Gasket.If you are taking on a complete engine overhaul... a) good for you, and b) us...

Floor Screws and Spire Nuts. Package of 10x FS-320045 and 10x FS-302532

LED Headlamp Black 7" H4Fits Series 1-3, Defender, and RRC. PAIRLamps have the H4 Plug which plugs right into your standard light wiring harness.DO...

Brake Light Switch, Hydraulic Pressure on Pipe UnionSeries 2 and 2aNote that this Switch has 1/8"NPTx27TPI and must be used on the 5-way union foun...

Rotor Arm for Series 1 2.0L and Series 2-3 2,25L 4 Cylinder up to Series 3 Eng Suffix C 54-74.For Lucas DM2 & 25D4 DistributorsNot for Ducellie...

Lucas Classic Sports Coil.For 2.25/2.5L 4 Cylinder Engines, Series and Defender.

License Plate Light Assembly Series 2-3, Defender (Some S1)

Lock Cylinder and Keys, Ignition Series 1-2a Gas 1948-71 Series 3 and Defender without Steering Column Lock. Also used on Series 3 Anti-Burst Door ...

Ignition Contact Points Fixed for Series 1 to 3, 1954-76.Fits Series 1 Late Lucas DM2 LU 40504A Distributor, Series 2 to 3 Lucas 25D4 and 25D6 Dist...

Glass Fuse 35AMP 17AMP Continuous for Series 1-3 OEM

Delphi AP Brake Pad Set Front. Defender 110 and 130 1986 onward. Defender 90 with Solid Rotors from 1991 to 2016. Defender 90 with Vented Rotors fr...

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.