Aftermarket

Brake Pipe Clip Stand-Offs Plastic

Bulkhead Outrigger LH or RH Series 2-3 88"/109" 1958-84

Bosch Fuel Pressure Regulator for TD5 Defender, Discovery 2.See EF-TD5REGKit for Gaskets and O-Rings required for full rebuild of the Regulator.

Brake Caliper Front Left Hand for Vented Rotor.For Defender 90, 110 and 130, 1994 to 2014.

Bottom Seal for Rear Door Threshold Series 2-3, Defender 90 and 110. For Full Size Rear Safari Door.

Brake Light Switch 1968-84 No Brake Servo. Suff F>

Brake Drum 11" 107/109" Series 1-2a, 1954-68.

Brake Drum Screw Series 1-3 1948-1984 Each.For a Package of 10, see BB-1510-10.

Brake Kit Rear Axle Set, 4-Cylinder, SWB 88", from July '80** If Sold Out, Use BB-DA6042 (Exactly the same)**Kit includes;1x STC2796 10" brake shoe...

Brake Caliper Front Right Hand for Vented Rotor.For Defender 90, 110 and 130, 1994 to 2014.

Bolt Kit for Galvanized Bumper CP-564704 to Chassis Series 2-3.

Bolt 1/4" BSF x 5/8" for Seal Retainer Plate to Swivel Hub. OEM.Series 1-3 You are purchasing 1, not 10 as shown in the photo.Supersedes BN-237140.

Blanking Plug for Bulkhead 3/4" Panel Hole Blk Rubber

Base Plate for Interior Mirror Defender 90/110 LR Genuine

Bearing for Primary Pinion (Front of Main Shaft) Gearbox Series 1-3

OEM NTN Clutch Release Bearing Series 1 to 2A, 1948-71Used for both 9" and 9-1/2" Clutch. 2.25L and 2.6L NADA.Also used on Front Output of LT230 fo...

Bell Housing to Transmission Gasket S1-3, 48-84

AVM Free Wheeling Manual Locking Hubs 10-SplineFor Series 1 through 3, to 1980 with 10-Spline Hubs.They're Back Baby! Easy to install, even easier ...

9.5" Clutch Cover Assembly Series 2a 1964-71 Use with Clutch Plate CC-FRC2297 and Bearing CC-STC1130.

Air Filter, Fits:Discovery 1 V8.Discovery 1 2.0L MPI Gas from VIN: MA081992.Range Rover Classic V8 and Range Rover Classic 300Tdi.For the Defender ...

Air Filter for Defender 90/110/130 300Tdi.

Air Filter Defender TD5, Discovery 2 V8 and TD5, Range Rover P38 2.5TD and V8

Aluminum Wing Top Protectors Series 2, 2a, 3 (Pair). Requires 20x RV-782-716 Pop Rivets

Copper-Nickel Clutch Pipe Master to Hose LHD Defender to 1998.

Brake Rotor Rear Solid Defender 110/130 from XA159807('99on). This is for both ABS and Non-ABS 110 Rear. Use Brake Pad Fitting Kit BB-DA4105 up to ...

Parabolic Springs PAIR 3 Leaf Rear with U-Bolts and Nuts. For Short Wheel Base 86", 88", or Long Wheel Base, 107", 109". Series 1-3. Note: For Heav...

Front Parabolic Springs Pair 2 Leaf with U-Bolts.Series 1-3, 86, 88, 109". *Note: a $40 surcharge for additional packaging will apply to this sale....

Rear Body Nut Plate and Fasteners for Series and Defender to 2002.Plate is Aluminium with Stainless Nutserts, Bolts and Washers Stainless Steel, Ri...

Oil Seal for the Output Shaft, Front or Rear, on the LT230 Transfer Case. For Defender, Discovery 1 and Range Rover Classic.

All three Knobs and the Spring for your Series Gear Shift Set. Main Gear Lever (Black Screw-On type with Brass Insert - Pancake), Transfer Gear Cha...

Raptor 4x4 Replacement Steering Box for Left Hand Drive. This steering box fits 300Tdi, Td5, and Tdci Defenders, Discovery 1 and Range Rover up to ...

Prop Shaft Nut Special Tool 1/2" Drive. Because regular sockets just don't fit... For Series, Defender, Discovery 1 and 2, Range Rover Classic and ...

O-Ring for Crankshaft Belt Sprocket on 300Tdi

Water Pump Overhaul Kit 2.25L Series 2, 2a and 3 1958-1984 Works for both the 8 hole, (Series 2, 1958-61, unobtainable pump 501041), and the 9 hole...

WE CAN NOT SHIP PAINT OUTSIDE OF CANADA Paintman Paints Limestone Land Rover Series and early 90s and 110s, 1959 to 1984. 500ml can.  Mainly used o...

Gasket for TD5 Turbo to Manifold. For Defender, and Discovery 2 with the TD5 engine. OEM ELRING, Made in the UK.

Gasket Exhaust Manifold to Cylinder Head V8 3.5/3.9/4.0/4.6L (4 Required, 2 Per Side).

Valve Seal (O-Ring Type) for Series 1 1.6 and 2.0L Inlet and Series 2-2a 2.25L Exhaust to 1968. 1.6L from Eng #061106720 on. 2.25L to March 1968 En...

Fuse Box Cover for the Puma Defender, 2007 on

Raptor Steel Instrument Panel Heater Control End Plate. For Defender 1983-06. This is a direct replacement for the poor plastic original LHD End Pa...

Raptor Engineering's Steel Binnacle (Instrument Panel Face), for Left Hand Drive from 1983-2000, (before the TD5 Facelift).This is a direct replace...

Bushing for Front Sway / Anti-Roll Bar Defender HD Susp

Rear body mount 3mm aluminium for All Rear Tubs. Fits Series 2 to 3 and All Defenders but the High Capacity. For the Chassis to Body Nut Plates, se...

Bushing Kit, Lower Link Trailing Arm to Chassis (Pair of SS-NTC9027).For Defender 1983-2016, Discovery 1 1989-1998, Range Rover Classic 1987-1995. ...

Standard Brass Bullet Connector 2.0mm2, 16 to 12 Gauge Wire.Suitable for crimping or soldering.For a Complete Kit of Various Sized Bullet Ends and ...

Standard Brass Bullet Wire End Connector 1.0mm2, 20 to 18 Gauge Wire.Suitable for crimping or soldering.aka: WH-541684.For a Complete Kit of Variou...

Wiper Tube End Piece for Wiper Drive Cable Assembly.For Series 2a and 3 from 1968, Defender to 2016.Supersedes WW-575047.

Cover for Door Check Right Hand Front Door Black.For Defender 1983 on.