Aftermarket

Pulley for Alternator on Series 2a/3 Gas or Diesel. Internal Shaft Diameter is 0.59", 15mm. Be sure this fits your Alternator.

Pop-Rivet Aluminium. 3/16"x1/2" Maximum Clinch 9/32" Sealed End, Aluminium Stem. For a Package of 10, see RV-78248-10 (linked below).

Power Steering Pump for 300Tdi Defender, Discovery 1. For Earlier (200Tdi) see SC-NTC9070. For Later (TD5) see SC-QVB101350 (linked below).

Propshaft, (Drive Shaft), Front for Series 1-3 4 Cylinder 1956-84.Fits Series 1 88" and 109", 1956-58.Fits Series 2-3 88" and 109" 4 Cylinder, (Not...

Peg for LT76 Gearbox Mainshaft Series 1-3, 1948-84 For the other Peg, see GT-RTC1979 (linked below).

Outer Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Inner Hub Bearing, see AD-RTC3416 (linked below left). For ...

Copper Oil Pan Drain Plug Washer. For 300Tdi, (see note below), 2.0L MPI, and Range Rover P38 4.0, 4.6L V8. For a replacement Plug, see EP-UAM2957L...

Oil Filter for 200/300TDI 2.5G/D, 2.5TD, V8-Gas

Oil Filter Coopers for 200/300TDI 2.5G/D, 2.5TD, V8-Gas

This is the left rear mudflap for the Defender 110/130, mounted on the steel bracket. No logo, just plain black.Matching flap for the right side i...

Nut 5/16" BSF for Various Uses. Note: You are purchasing 1, not 5 as shown in the photo.

NTN Outer Hub Bearing Series 1 Front, Series 2/2A/3 Front and Rear up to 1980. For Inner Hub Bearing see AD-RTC3416G (linked below left) For a comp...

NTN Inner Hub Bearing Series 1 Front, Series 2, 2A and 3, Front and Rear up to 1980. For Outer Hub Bearing see AD-RTC3426G (linked below left) For ...

Nut Retainer for Door Handle/Lock Assembly For Series and Defender Pull-Up Door Handles. 1 Required per Door Handle. Requires 2x Bolts BN-SE106161L...

Nut Spire for Front Wing to Bulkhead Series 2-3, 90/110

Master Cylinder Rebuild Kit for Series 1 SWB, 80, 86, and 88" 1948-58 For Original 3-Bolt Master Cylinders 235006 and 241687. For a Kit of just the...

Lucas 25D4 Type Electronic Ignition Distributor Negative Earth for 2.25L Series 2-3. Also Works on the Series 1 2.0L Engine, Negative Earth of cour...

Mirror Head 4-1/2" Round Series 1-3 (No Arm)

Leaf Spring Kit for Series 1-3 86/88" LHD Standard with U-Bolts. Standard Duty Set of Leaf Springs and U-Bolts. *Note: a $40 surcharge for addition...

Locker Plate for Swivel Pin Series 1-2a 1948-1962 3/8" Studs 4 Required per Side, 8 per Axle. You are purchasing 1, not 10 as shown in the photo.

Lens for Front/Rear Indicator, Euro Amber Plastic 2-5/8" Dia

Joint Washer (Brass) for Oil Seal Retainer on Rover Differential. NOS. Series 2-3, 1958-67. Check your Differential first. This will not work on ea...

Indicator Switch Horn and Headlamp Dip Defender up to VIN GA455945, 1990. For Later, see BE-STC439 (linked below).

Instrument Panel Rear Cowl for Defender Left Hand Drive with In-Dash Factory AC, up to 2006. Plastic. Typically broken when taking the dash apart. ...