Aftermarket

Washer Special for Clutch Clevis Pin & Other Uses.Supersedes CC-10882.

Return Spring for Accelerator Pedal.For Series 1 1948-58.

Stud for Timing Cover. For Series 1 and 2, 2.0L Diesel 1956-62.For Series 2, 2.25L Gas to 1961.1-Required. This is the Shorter Stud. 5/16" UNF x 3-...

Copper-Nickel Pipe from the Remote Servo to the 5-Way Junction.For Series 2a 109" NADA 6 Cylinder.

Head Gasket De-Carb Top End Set for Series 1 2.0L 1951-54 ("Siamese Head"). For a Bottom End Gasket Set see EG-270568BE (linked below).

Head Gasket for 1.6L Series 1 Engine 1948-51. For a Full Top End Gasket Set see EG-261407 (linked below).

Head Gasket for Series 1 2.0L 1951-54 (Siamese Head). For a Full Top End Gasket Set see EG-262102 (linked below).

Bracket for Lower Steering Column Shroud.For Series 3 Left Hand Drive. This holds the Lower Steering Column Shroud, BP-347558, to the Dash Assembly.

Flanged Hex Head Bolt M10 x 110mm For Various Uses.Supersedes BN-RYP500140.

Nakatanenga Heritage Style Grill Black Non-AC with Stainless Steel Screws. Fits Defender without AC

Nakatanenga Heritage Style Grill Silver Non-AC with Stainless Steel Screws. Fits Defender without AC

Master Cylinder Series 1 80" 1948-53 3-Hole Reproduction For Series 1 80" 1948-53 with 1/4" brake pipes. Supplied without Push Rod. * This will Shi...

Wheel Cylinder Rear Right HandFor 80" Series 1, 1948-53.Inlet is 7/16" UNF for 1/4" Brake Line.Note: You will Require 2x BN-NH605041Y8 and 2x BN-WM...

Wheel Cylinder Rear Left HandFor 80" Series 1, 1948-53.Inlet is 7/16" UNF for 1/4" Brake Line.Note: You will Require 2x BN-NH605041Y8 and 2x BN-WM6...

Wheel Cylinder Front Right HandFor 80" Series 1, 1948-53.Inlet is 7/16" UNF for 1/4" Brake Line.Note: You will Require 2x BN-NH605041Y8 and 2x BN-W...

Wheel Cylinder Front Left HandFor 80" Series 1, 1948-53.Inlet is 7/16" UNF for 1/4" Brake Line.Note: You will Require 2x BN-NH605041Y8 and 2x BN-WM...

Door Capping Galvanized Right Hand.Rivetted to Door Bottom, Between the Door Top and Door Bottom.For Series 2-3 1958-84.

Joint Gasket for Top Cover of Solex 32PBI-2 Carburetor. For Series 1 1.6L and 2.0L. For a full Carburetor Gasket Set, see EF-274895 (linked below).

Gasket Cork for Rear Water Jacket Series 1 1950-58 & 2.6L

Radiator Coolant Hose Bottom, Radiator to ThermostatFor Discovery 2.

Polyurethane Suspension Bushing Kit Yellow. Defender 1999-2007 There is no difference between the black and yellow kits other than the colour.  It'...

Bushing Kit Poly-Urethane Yellow Radius Arms to Axle.For Defender up to VIN: KA930455 (1993), Range Rover Classic to Oct/1985.Supersedes SS-NTC1774...

Bushing for Front of Radius Arm.For Defender up to KA930455 (1993), Range Rover Classic to Oct/1985.Supersedes SS-NTC1774.

This is the Rear Main Oil Seal for the 3.5L, 3.9L, 4.0L and 4.6L V8. Corteco OEM.It fits quite a few trucks, including the Discovery 1 and 2, the R...

Flasher Relay Electronic 3-Pin Black without Trailer Socket.For Defender from VIN: MA939976 (1995 MY), Discovery 1 and Range Rover Classic.

Clutch Release Bearing for LT77 and R380 with the 2.0L MPI Engine in Discovery 1, or the Italian Defender 90 with the 2.0L MPI Engine.Longer body c...

LOF Clutch Pedal Assist Kit Spring and Bushings. Defender 1994on Replace the old clutch pedal spring kit to assist the pressing of the clutch pedal...

Rubber Seal for Windscreen to Roof.Series 1, 1954-58.Note: This does Not Include the Stiffening Metal Strip.

Rubber Seal for the Bulkhead to the Windscreen.Series 1 80", 1948-53.

Square Washer for Series 2-3 109" Station Wagon Fuel Tank Mounts.Typically 4 Required.

Defender 90 200Tdi Complete Exhaust System. Includes SE-ESR158 Front Down Pipe, SE-ESR358 Front Silencer Intermediate Pipe, SE-ESR254 Rear Silencer...

Rear Crankshaft Oil Retainer Seal Series 1 2.0L Gas 1955-58.

Locker for Cam Thrust Plate Series 1 1.6/2.0 & S2a 2.6L

Engine Bay Decal "Smiths" Heater

Pop Rivet Alum 3/16"x9/16" Max Clinch 5/16" Sealed End

Adapter for Wiper Arm 14.8mm Splined to 1/4" "D" Profile.Some Series 3 with the "D"-Profile Wiper Shaft. Also used on Defender up to VIN: 1A622423 ...

Exhaust Clamp Bracket for Intermediate Pipe.For Series 1 to 3, Typically 2 Required.

Pop Rivet Alum 3/16"x3/4" Max Clinch 1/2" Sealed End

Exhaust Valve Seat Oversize .005.For Series 1 1.6L and 2.0L, 1948-58, and Series 2a 2.6L 6 Cylinder.

Spring Oil Pressure Release Valve Series 1 1954-58

Output Shaft Front for Series 1 to 3 1948-84.Supersedes GT-233248.This item is Old New Stock.

Circlip for Adjuster Arm to Pivot Pin Series 1 1.6L and 2.0L Gas Engine.Supersedes EP-09129 and EP-9129.

Circlip for Timing Chain Idler Wheel.For Series 1 1.6L, 2.0L 1948-58.Supersedes EP-09128 and EP-9128.

Ball for Oil Pump Release Valve on Series 1 1948-58 and 2.6L 6 Cylinder.

Spring for Timing Pawl Chain Tensioner Series 1 1.6L and 2.0L Gas Engine.

Clamp for Steering Drag Link or Track Rod or Longitudinal Rod

Radiator Only for 300Tdi Heavy Duty All Metal Copper Core with Brass Ends.For Defender, Discovery 1 and Range Rover Classic.For the Less Expensive ...