New products

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Swivel Hub Seal Retainer 1948 to 1984, Series 1-3.For a Kit with the Seals and Correct Bolts and Nuts, see SC-SOSKITST.

Gasket Paper for Swivel Hub to Axle Case 1948-1984

Gasket Paper for Stub Axle Rear.For Series 1 through 3, from 1957 to the end of 1984.

Gasket for Stub Axle to Swivel Hub Front, Series 1 to 3, 1954-84

Drive Flange Gasket Front 1948-84 or Rear 1958-1984

GKN OEM Universal Joint for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Universal Joint, (U-Joint), for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Universal Joint for Front or Rear Propshaft.Fits the Series 2a-3, 1964-84, and the Land Rover 90/110 until 1985.3-7/32" (82mm) Across the yoke, end...

OEM Universal Joint for Series 1 to Some Early Series 2a, 1948-64.GKN Hardy Spicer.Greasable. 2-15/16" (75mm) Across the yoke.Measure before you bu...

O-Ring for Thermostat Housing Series 2 1958-60

Radiator Hose Kit for Series 1 1948-58 1.6L and 2.0L EnginesIncludes EC-268037 and EC-268038 with Stainless Steel Clamps.

Radiator Hose Kit for Series 2 and 2A 1958-68 With Stainless Steel Hose Clamps. Not for use with Later Series 2a/3 Replacement Radiator; see EC-H...

Hardened Valve Seat Insert for Exhaust Valve for 2.25L Gas Engine.Series 2 to 3 2.25L Gas and Defender 2.25L and 2.5L Gas.Santana, Made in Spain.

Universal Joint for Series 1 to Some Early Series 2a, 1948-64.Greasable. 2-15/16" (75mm) Across the yoke.Measure before you buy please.

Prop Shaft Rubber Gator and Clamps. All Series trucks and Early Defenders. For a Pair of these, see AP-276484PR (linked below left) For the later D...

Hub Cap - Series 3 from October 1983 (black plastic). Land Rover 90/110, and Defender to 1993. From 1994 onward, you'll want FTC5414 (linked below).

Series Hub Cap, Metal, up to September of 1983.

Swivel Housing Kit with Ball Series 2a-3, 1967-84 LH or RH.Does One Side, Left-Hand Or Right-Hand.For an Axle Set of all Bolts and Nuts Required, s...

Swivel Housing Kit with Ball for Series 1-2a, 1950-67 Does One Side, Left-Hand or Right-Hand. Includes Parts to Complete a Railko Conversion to lat...

Series 2a and 3 Swivel King Pin, Bearing and Seal Kit. Full Axle Set.Does Both Swivels. Includes Top Pins, Bushings, Bottom Bearings, Thrust Washer...

Series 1, 2, and 2a Swivel Pin Railko Conversion Kit, Full Axle Set.Does Both Swivels.For Converting older style Swivel Pin Housing Units to King P...

Hub Bearing and Oil Seal Repair KitFor the Series 2/2a/3 88" from July of 1980. 109" from October of 1980

Hub Bearing and Oil Seal Repair Kit. Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully Floating Axles on 109", and 88" with the optional full ...