New products

Swing away rear spare wheel carrier for Defender half-door or drop-down tailgate. With fittings and instructions.

Crystal Halogen Head Lights for LHD 7" Pair.Note: Bulbs Not Included, see LB-589783 (linked below).For Series, Defender and RRC.Better Night Time V...

Reverse Gear Shaft for Series 1-2a, 1948-71. For later Series 3 Gearbox Suffix A, see GT-591527; for Series 3 Suffix B onwards, see GT-FRC1813. SPE...

Reverse Gear Idler Shaft for Series 3 Suffix A Gearbox Only, 1971-72.For Earlier, see GT-561962 (SS: GT-06424). For Later Series 3 Suff B onwards s...

Reverse Shaft Series 3 Gearbox Suffix B Onwards. From September 1972. For the Earlier Series 3 Suffix A Gearbox, see GT-591527. SPECIAL ORDER: Plea...

Heater/Glow Plug for 200Tdi (1989-1994) & 300Tdi (1994-2006)

Heater/Glow Plug for 200/300Tdi Engine OEM Bosch.

Fuel Filter for TD5 Defender 90/110, Discovery TD5 Cooper

Bracket for Rear Anti-Roll / Anti-Sway Bar - Single Bolt Type.For Defender 90 ROW up to 1998.For the Later Defender 90 Bracket with Two Bolt-Holes,...

Bracket for Rear Anti-Roll / Anti-Sway Bar.For Defender 90 1994on. Uses Bushing SS-EGP1889 (linked below).For the Earlier Defender 90 Bracket with ...

Bracket for Rear Anti-Roll Anti-Sway Bar Bushing.For Defender110/130 with the 4-Bolt Bracket. For Defender 2-Bolt Type, (Some Defender 110/130's an...

Bolt for Anti-Roll Bar (also called a Sway Bar) to Ball Joint Front or Rear for Defender 90, Discovery 1 and Range Rover Classic.Requires Metal-Loc...

Bushing for Rear Sway / Anti-Roll Bar.For Defender 110/130.Not for 110 V8, or Defender 90, See SS-NTC7394 or SS-EGP1889.

Bushing for Anti-Roll / Anti-Sway Bar.Fits Defender 90 up to VIN: WA159806,(to 1998), Discovery 1 and Range Rover Classic.

Idler Wheel for Timing Chain.For Series 1-3, 2.0L Diesel, 2.25L Gas and Diesel.

3 Brothers latest shirt is our favorite yet. A Series 2a on the front with our wordmark and shop address on the back. Both printed in Land Rover Li...

Water Temperature Sender for V8 Carburetor.For Range Rover Classic to 1991, Series 3 Stage 1 V8, and 101 Forward Control V8.

Pipe Adapter for Emission Hose on Carburetor Adapter or Inlet ManifoldFor Late Series 2a and Series 3.You might need the Copper Seal, see CS-243958...

Hose Elbow for Crankcase Vent Control to Carburetor Adapter Port. For Some Early Series 3. Note: This is a 3" x 3" Rubber Elbow. Later Series 3 use...

Hose Elbow for Emission System, from Carburettor Adapter to Crankcase PCV Vent Control Series 3 up to Suffix C, (August 1974) Note: This is a 2" x ...

Hose, Breather to Air Intake Elbow 2.25L Gas.For Series 3 North American Standard, and Engine Prefix 901 and 904 Suffix C and D.

2.25L Connecting Rod Gudgeon Pin Bearing

Stepper Motor IAC (Intake Air Control) for V8 EFI.For RRC and Defender.

Cellular Dynamic Extended Shock Kit for 109" Front and Rear. Includes 4 Extended Length Shocks and the Required Bolts, Nuts and Washers to Mount th...