New products

This is a rubberized end cap for the Defender's front bumper.Fits either side on the standard bumper starting in 1984 all the way through the end o...

Set of 3 Replacement Rubber Grommets for Series 1 1953-58. Handbrake, Gear, and Transfer Lever. Note: Handbrake has a Round Hole for Round Shaft an...

Land Rover Genuine Oil FilterFits 2.5 Gas or Diesel, 2.5 Turbo-Diesel,200Tdi, 300Tdi, and 3.5/3.9/4.0/4.2/4.6L V8-GasDefender, Discovery 1, Discove...

Anti-Burst Door Handle Kit for Series 2-3, Does the 2 Front Doors. Everything needed to convert the old Slam-Type handles to the later Anti-Burst h...

Anti-Burst Door Handle Kit for Series. Does the 2 Front Doors and the Rear Safari Door. Everything needed to convert the old Slam-Type handles to t...

Pedal Pad for Brake or Clutch Defender (RoW) upto 1986

Support Bracket LH for Rear Bumper End Cap RRC '86on

Support Bracket RH for Rear Bumper End Cap RRC '86on

Plastic Clip for Bonnet Prop Single on Discovery 2 and Defender from 1998-2106 OEM

Front Door Sill Panel RH Defender 90/110

Front Door Sill Panel LH Defender 90/110

Adhesive Patch for Interior Mirror to Glass LR Genuine

Gasket Paper for Clutch Withdrawal Housing. For Series 1 to Series 2a, 1948 to 1962, up to and including Gearbox to Suffix A. AKA EG-90213663. For ...

Spherical Bearing Cover for Clutch Cross Shaft and Left-Hand Drive Hand Brake. Series 1 to 3. Typically, 2 Required.

Bushing for Clutch or Brake Pedal Shaft Series 2-3

Banjo Bolt for Clutch Slave CylinderFor Series 2a LHD with 1/4" Pipes. Note: the Banjo 538068 that this goes through is no longer available.For Ser...

Clutch Slave Repair Kit RRC 70-94, D1 89-94, 90/110, LT77

Clevis Pin for Clutch Cross-Shaft Series 1-2a For Series 1 to 2a, 1948-71. For Complete Kit with washer and cotter pin, see CC-536803KIT (linked be...

Connecting Tube for Clutch Throw Out Cross Shaft.For Series 2 to 2a.

Set of 3 Replacement Rubber Grommets for Series 2a-3 1967-84.Handbrake, Gear, and Transfer Lever.Handbrake has Oval Hole. This set can work for ear...

Clip for Clutch Release Throw-Out Lever S3, Def, RRCto'94, D1

9.5" Clutch Cover Assembly Late 2a,S3,Def2.5G,D1 MPI OEM

Pivot Pin for Clutch Release Fork on Series 3 Clutch

Cap for Pivot on Clutch Release on Series 3

Retaining Clip for Clutch Release Push Rod Series 3 Defender TD5 with R380 Discovery 1 V8 with R380 For LT77 and Tdi/R380 See CC-FRC3327

Lucas R401 Voltage Regulator Series 1, 2 and Early 2A 1948-65.Screw-Type Connectors. For use with Dynamo, (Generator).Supersedes EE-217277, EE-2355...

Clevis Pin with Washer and Cotter Pin for Clutch Cross-Shaft Series 1-2a. For Series 1 to 2a, 1948-71. Supersedes CC-240191.

Bolt Kit for Series 2, 2a and 3, 1969 to 84, Right and Left Hand Mud Shield Splash Guards. Correct Fasteners for Doing Both Sides for LHD and RHD. ...

Fuel Tank Bolt Kit for S2-3 109" Stn Wgn up to Stuff B -1969. Note this kit does not include all parts required. This replaces the bolts, nuts, was...

Set of 3 Replacement Rubber Grommets for Series 2/2a 1958-66. Handbrake, Gear, & Transfer Lever. This Handbrake grommet does not fit Series 1 1...

Service Kit for Td5 Oil, Air, Fuel and Rotor Filters, Washer. Defender or Discovery TD5, 1999 to 2006.

Gasket for Clutch Master Cylinder Series 3, 90/110 OEM

Oil Seal for Clutch Cross-Shaft Series1 RHD and Series 2/2a Left- or Right-Hand Drive; 1948-71. For the Series 1 LHD Oil Seal, see CC-219988 (linke...

Cap for Clutch Release Pivot Pin for R380 TD5 & V8

Clip for Clutch Release 4 Cyl LT77/R380, D1-2.0Mpi

Push Rod for Clutch Slave Cylinder 4-Cylinder with LT77 Gearbox.For Defender, and Discovery 1 to 1994.