New products

Hose Clamp 7/16" - 1" Diameter x 9/16" Bandwidth Stainless for Various Uses

Hose Clamp 11/16" - 1-1/2" Diameter x 1/2" Bandwidth Stainless Various Uses

Hose Clamp 1/2" - 1-1/2" Diameter x 5/16" Narrow Bandwidth Stainless Various Uses.

Hose Clamp 3/4" - 1-3/4" Diameter x1/2" Bandwidth All Stainless Various Uses.

Hose Clamp 1" - 2" Diameter x 5/16" Narrow SS Band Steel Screw

Hose Clamp 1-3/8" - 2-3/8" Diameter x 5/16" Narrow Bandwidth Stainless Various Uses.

Hose Clamp 1-1/2" - 2-1/2" Diameter x 1/2" Bandwidth Stainless Various Uses

Hose Clamp 2" - 3" Diameter x 1/2" Band All Stainless.For Various Uses.

Hose Clamp 2-1/4"- 3-1/4" Diameter x 1/2" Bandwidth All Stainless Various Uses

Hose Clamp 2-1/2"-3-1/2" Diameter x 9/16" Bandwidth Stainless for Various Uses.

Hose Clamp 2-3/4" to 3-3/4" Diameter x 1/2" Bandwidth Stainless Steel Band.For Various Uses.

Hose Clamp 3" - 4" Diameter x 1/2" Bandwidth All Stainless For Various Uses.

Rope Cleat for Side of Rear Tub Series and Defender (Rivet-on). You'll need 2 or 3 Rivets RV-78248 to fasten to the body side.Normally you require ...

Clamp Arm (Claw Hook) for Securing Hoop Stick to Tub.For Series 1-3 and Defender.

Front Rope Tie-Down for Full Hood 88/109" Right Hand. Properly Galvanized. See HH-330579 for the Left Hand Side (linked below left); or, For a Kit ...

Front Rope Tie-Down for Full Hood 88/109" Left Hand. Properly Galvanized. See HH-330578 for the Right Hand Side (linked below left); or, For a Kit ...

Hood Stick Set for a Full Canvas Hood.Fits 88" SWB Series 2-3, 1958-84.Can also be used for the Bikini Hoods by removing the rear hoop and cross bars.

Canvas Top 88" Full Hood with Side and Rear Windows Sand, for Series 2 to 3.All Wheel Trim Product. Long-Lasting, Excellent Quality!

Rope Tie-Down (U-shape) on Rear Tub for Canvas Top. OEM.Zinc Coated. For Series 1-3 and Defender. Requires 2 Rivets, RV-RU612373.

Battery Hold Down Frame for Series 1-3. For the J-Clamp Rods, see FS-562953L, or FS-562953Kit (linked bleow).

Universal Joint Heavy Duty Greasable.Fits Defender 90, on both the front and rear from VIN CA252578 to 1A612044, (to 2001).Defender 110/130 All Rea...

Exmoor Trim 88"/109" Bikini Hood Stick Set Series 2-3For the Canvas Bikini Tops to go with this, type "Bikini" in the search window.

Spring for MTC4583 Spindle for Handle Fixing Hood Header

Spring Pin for MTC4583 Spindle for Handle - Hood Header You are purchasing one, not ten as shown in the picture

Staple for Hood Strap on Rear Tub and on Windscreen Rail.For Series and Defender.You are Purchasing 1, not 10 as shown in photo.

Retaining Clip for Heater Control Cables 90/110 to 2006 OEM.  You generally need two of these. Note: You are purchasing 1, not 10 as shown in the p...

Screw for Heater Trunnion on Valve Series 3

Rubber Grommet for Heater Box Hoses Series 3 1971-84

Rubber Grommet for Heater Box Hoses Series 3 1971-84

Front Outer Wing Trim for Heater Air Intake.For Series 3, Plastic and Metal Grill.Note: This is for the 5" Hole in the Front Outer Right Hand Wing,...

Air Hose for Heater Blower to Heater Unit, OEM.For Series 2a to 3; Smiths 2-Piece Heater Assembly. This hose connects the Heater Blower to the Heat...

Heater Intake Seal to Front Wing Series 2a/3 1972-84.Quality Made from High Density 1/2" Neoprene Foam. Made in Canada!

Series 3 Demister Tube (RH or LH) 2 Required

Knob for Hot/Cold on Heater Control Series 3 Genuine

Heater Air Duct Outlet to Floor RH Series 3 / Defender to '06

Heater Air Duct Outlet to Floor LH Series 3 / Defender to '06

Defrost Demister Vent Dash Top Cover.For Series 3, 1975 to 84.These are 10.75" wide, adaptable for the early Defender vents, (to 1988), HS-MTC6040,...

Trunnion for Heater Air Control Cable Series 3 and 90/110

Heater Hose Core In/Out to Pipes for Late Series 2a and 3 Smiths Type Heater.For 4 and 6 Cylinder Left Hand and Right Hand Drive.2 Required for LHD...

Heater Hose Valve to Pipe for Series 3 LH and RHD

Heater Hose Heater Core to Block RHD Series 3

Heater Hose Pipe to Head LHD Series 3

Adapter Pipe for Rear Heater Hose to Engine Cylinder HeadSeries and Defender. Gas and Diesel.OEMThe Thread on this Adapter is 3/8" BSF.Requires Cop...

Heater Control Valve, Brass for Series 2, 2a 1958-71. The Copper Seal needed for this is CS-243959 (linked below).

Heater Control Valve Assembly for Series 3 LHD or RHDOEM, Made in the UK.

Heater Matrix for Defender - Downward In/Out Pipes Up to VIN:WA159806, 1998, If your Heater has Horizontal In/Out Pipes, see HS-UTP1725 (linked bel...

Control Cable for Heater Outlet Main Air Valve. Actuated when turning on the Blower.For Defender to VIN: 2A633474, 2002.For later see HS-JFF000140 ...

Heater Hose Inlet Defender TD5 LHD