Newest Products

Filler Strip for Front Door Glass Vertical Rear Left or Right Hand. Fits Defender 90, 110, and 130 from 1987-2016 except NAS.

Oil Filter Element for 5.0L V8 LR4, RR-L320 RR-L322

Gasket Paper for Inlet Pipe to Water Pump Series 1 1.6L and 2.0L, 1948-58.

Gasket Fiber for Inlet Elbow or Water Outlet Pipe.For Series 1 1.6L and 2.0L Gas Engine, 1948-58

Valve Plug (Grub Screw) in Timing Piston 2.25L Gas.For Series 3 2.25L Engine up to Engine SN: 90290283E and 9045259E.

Locating (Grub) Screw for Oil Pump / Distributor Shaft.

B-Post Full Repair Section Series or Defender, 4/5 Door, Left or Right Hand.Note these are only for Push-On Door Seals, not for the Rivet-on Seals....

Air Intake Grill for Defender 2.5L Turbo Diesel and 200Tdi to 1994. For later model 300Tdi/Td5, please refer to BP-BTR6188

Cellular Dynamic Extended Shock Kit for 109" Front and Rear. Includes 4 Extended Length Shocks and the Required Bolts, Nuts and Washers to Mount th...

Stepper Motor IAC (Intake Air Control) for V8 EFI.For RRC and Defender.

2.25L Connecting Rod Gudgeon Pin Bearing

Hose, Breather to Air Intake Elbow 2.25L Gas.For Series 3 North American Standard, and Engine Prefix 901 and 904 Suffix C and D.

Hose Elbow for Emission System, from Carburettor Adapter to Crankcase PCV Vent Control Series 3 up to Suffix C, (August 1974) Note: This is a 2" x ...

Hose Elbow for Crankcase Vent Control to Carburetor Adapter Port. For Some Early Series 3. Note: This is a 3" x 3" Rubber Elbow. Later Series 3 use...

Pipe Adapter for Emission Hose on Carburetor Adapter or Inlet ManifoldFor Late Series 2a and Series 3.You might need the Copper Seal, see CS-243958...

Water Temperature Sender for V8 Carburetor.For Range Rover Classic to 1991, Series 3 Stage 1 V8, and 101 Forward Control V8.

3 Brothers latest shirt is our favorite yet. A Series 2a on the front with our wordmark and shop address on the back. Both printed in Land Rover Li...

Idler Wheel for Timing Chain.For Series 1-3, 2.0L Diesel, 2.25L Gas and Diesel.

Bushing for Anti-Roll / Anti-Sway Bar.Fits Defender 90 up to VIN: WA159806,(to 1998), Discovery 1 and Range Rover Classic.

Bushing for Rear Sway / Anti-Roll Bar.For Defender 110/130.Not for 110 V8, or Defender 90, See SS-NTC7394 or SS-EGP1889.

Bolt for Anti-Roll Bar (also called a Sway Bar) to Ball Joint Front or Rear for Defender 90, Discovery 1 and Range Rover Classic.Requires Metal-Loc...

Bracket for Rear Anti-Roll Anti-Sway Bar Bushing.For Defender110/130 with the 4-Bolt Bracket. For Defender 2-Bolt Type, (Some Defender 110/130's an...

Bracket for Rear Anti-Roll / Anti-Sway Bar.For Defender 90 1994on. Uses Bushing SS-EGP1889 (linked below).For the Earlier Defender 90 Bracket with ...

Bracket for Rear Anti-Roll / Anti-Sway Bar - Single Bolt Type.For Defender 90 ROW up to 1998.For the Later Defender 90 Bracket with Two Bolt-Holes,...