Newest Products

Swivel Housing Kit with Ball for Series 1-2a, 1950-67 Does One Side, Left-Hand or Right-Hand. Includes Parts to Complete a Railko Conversion to lat...

Swivel Housing Kit with Ball Series 2a-3, 1967-84 LH or RH.Does One Side, Left-Hand Or Right-Hand.For an Axle Set of all Bolts and Nuts Required, s...

Series Hub Cap, Metal, up to September of 1983.

Hub Cap - Series 3 from October 1983 (black plastic). Land Rover 90/110, and Defender to 1993. From 1994 onward, you'll want FTC5414 (linked below).

Prop Shaft Rubber Gator and Clamps. All Series trucks and Early Defenders. For a Pair of these, see AP-276484PR (linked below left) For the later D...

Universal Joint for Series 1 to Series 3. All Defenders 90, 110, 130 from 1987- 2016, Discovery 1 and some Range Rover Classics. Greasable. 2-15/16...

Hardened Valve Seat Insert for Exhaust Valve for 2.25L Gas Engine.Series 2 to 3 2.25L Gas and Defender 2.25L and 2.5L Gas.Santana, Made in Spain.

Radiator Hose Kit for Series 2 and 2A 1958-68 With Stainless Steel Hose Clamps. Not for use with Later Series 2a/3 Replacement Radiator; see EC-H...

Radiator Hose Kit for Series 1 1948-58 1.6L and 2.0L EnginesIncludes EC-268037 and EC-268038 with Stainless Steel Clamps.

O-Ring for Thermostat Housing Series 2 1958-60

OEM Universal Joint for Series 1 to Some Early Series 2a, 1948-64.GKN Hardy Spicer.Greasable. 2-15/16" (75mm) Across the yoke.Measure before you bu...

Universal Joint for Front or Rear Propshaft.Fits the Series 2a-3, 1964-84, and the Land Rover 90/110 until 1985.3-7/32" (82mm) Across the yoke, end...

Universal Joint, (U-Joint), for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

GKN OEM Universal Joint for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Drive Flange Gasket Front 1948-84 or Rear 1958-1984

Gasket for Stub Axle to Swivel Hub Front, Series 1 to 3, 1954-84

Gasket Paper for Stub Axle Rear.For Series 1 through 3, from 1957 to the end of 1984.

Gasket Paper for Swivel Hub to Axle Case 1948-1984

Swivel Hub Seal Retainer 1948 to 1984, Series 1-3.For a Kit with the Seals and Correct Bolts and Nuts, see SC-SOSKITST.

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Hub Spanner Wrench for Hub Locking Nut 2-1/16" 52mm. For locknut FRC8700.

Hub Lock Washer. For Series 1-3, the whole run from 1948 through 1984. For Land Rover 90/110 and Defender Front Axles to VIN: KA930455, (1993) and ...

Hub Oil Seal - Metal and Rubber, Series 1 Rear Axle 1948-58.Series 1 with Semi-Floating Rear Axle Only.

Hub Oil Seal.Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full float axles from 1957 to...

Corteco OEM Hub Oil SealFits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full float axles f...

Felt Seal for Axle Shaft Front or Rear Hub Assembly1958 to 06/80. For Series 2-3. Series 1 Axles didn't use these for some reason.

Swivel Pin Bearing - Bottom of Swivel Housing. Series1-3.

Bearing for Half-Shaft Front 1954-1984 Series 1-3

Distance Piece for Half-Shaft Front (Bearing Holder) for Series trucks between 1954 through to the end in 1984.

Oil Seal for End of Front Axle Casing 1948-1984 Series 1-3

Axle Breather Valve Series 1-3 1948-84, and Range Rover Classic.

Gasket for Rover Differential, Front or Rear.For Series 1-3, Range Rover Classic 1970-95, Discovery 1 1989-98, Discovery 2 1999-04, Defender Front...

Thrust Washer for Differential Pinion Bearing Series 2a, 3, Land Rover 90/110, and /Defender OEM

Pinion Oil Seal for Rover Differential Front or Rear OEM For Series 1-3 1950-84l Supersedes AF-217507, AF-561360.

Mud shield for Front or Rear Rover Differential OEM

Brake Kit Front Axle Set, 4 Cylinder, 86/88", 10" Brakes, up to June '80, Kit includes; 1x STC2796 10" brake shoes axle set 1x 243296 right wheel c...