Newest Products

Brake Front 4-Way Fitting for Series 1 86" and 107" 1954-58 and Series 2a and 3 88" SWB and 109" LWB 1969 to June 1980 Brass. 4x 3/8" Imperial U...

Brake Rear 3-Way Tee Union.For Series 1 86" and 107" 1954-58 and Series 2, 2a, and 3, 88" SWB and 109" LWB up to June 1980.Brass. 3x 3/8" Imperial ...

Brake Front or Rear Tee Union for 88" SWB and 109" LWB from July 1980 Brass. Metric pipe union.

Clutch or Brake Master Cylinder Adapter 3/8"UNF Male to 7/16" UNF Female.Depending on the purpose, you will require BC-233220 Copper Seal and/or BC...

Brake Pipe Clamp Stainless Steel 88 and 109 Single 3/16" Brake or Clutch Line. Also used as a clip for roof lamp wire.

Brake Pipe Clamp Stainless Steel for 88" and 109"Single 1/4" Brake or Clutch Line.

Brake Pipe Clamp 88 and 109 Double 3/16" Line Stainless Steel.For side by side 3/16" Brake and Clutch lines.

P-Clamp for Brake Lines.For Series 1-3 Single or Dual Line 3/16 and 1/4" Pipes.Supersedes BC-50640.

Rubber Grommet for Brake Line P-Clamps 3/16"-1/4"

Brake Pipe Clip Stand-Offs Plastic

Front or Rear Brake Hose for Series 1 80" 1948-1953 7/16" UNF. For use on; Series 1 80" Front Left or Right, and Rear from 1948 to 1953. Also used ...

Front or Rear Brake or Clutch Hose, 86/88 107/109, 3/8" UNF.For use on:Series 1 to 2a, Front Brake, Left or Right, 86/88" SWB or 107/109" LWB, fro...

Rear Brake Hose 109" Series 2-3 up to June 1980, 3/8" UNF. For use on: Series 2, 2a, or 3, Rear, 109" LWB only, 1958 - June 1980. Series 2, 2a, or ...

Front Brake Hose 88" and 109" Series 3 1971 to June 1980, 3/8" UNF. For use on: Series 3, Front, 88" SWB or 109" LWB, 1971 - June 1980. Imper...

Front Brake Hose 88" and 109" Series 3 July 1980 to 1984, Metric. For use on; Series 3, Front, 88" SWB or 109" LWB, July 1980 to 1984. Metric M1...

Rear Brake Hose 109" Series 3 July 1980 to 1984, Metric. For use on; Series 3, Rear 109" LWB only, July 1980 to 1984. Metric M10 1.00 thread. (N...

Lock Washer Shake-Proof Int Tooth 7/16" for Series 1 Brake Hose & Series 2, 2a, 3 Clutch Hose.

Lock Nut for Brake Hose 7/16". Series 1 48-53, Series 2, 2a, 3, Land Rover 90/110, Defender Clutch Hose.

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.

Lock Washer Internal Tooth Zinc for 3/8" Brake Hoses 1954-1984. Also, for Defender 36-Spline Steering column.

Brake Hose Nut 3/8" UNF Zinc 1954 - June 1980. All Series.

Brake Hose Nut Metric 10mm Zinc Series 3, June 1980-84

Brake Light Switch, Mechanical Pull Type, Lucas Genuine.Series 1 to 2a.Used Externally as the Brake Light Switch on Series 1's. Used as the Choke L...

Brake Light Switch, Hydraulic Pressure on Pipe UnionSeries 2 and 2aNote that this Switch has 1/8"NPTx27TPI and must be used on the 5-way union foun...

Brake Light Switch 1968-84 No Brake Servo. Suff F>

Brake Light Switch, Series 3, 1971 to 1984 with Brake ServoAlso used as the Optional Reverse Light Switch on the Gearbox.

9" Clutch Plate for 1948-1969 Series 1-2a.For the Clutch Cover/Pressure Plate, see CC-591705.For a Complete Kit with the Cover, Plate and Flywheel ...

9.5" Clutch Plate Optional 1964-71, Standard 1970-84 Late 2A, Series 3 Optional 9.5" Clutch used on NADA Gas/Dsl 88 and 109, 1964-71. Standard on D...

9.5" Clutch Cover Assembly OEM-AP Drive Series 2a 1964-71 Use with Clutch Plate CC-FRC2297G and Bearing CC-STC1130G.

Clutch Release Bearing Series 1 to 2A, 1948-71Used for both 9" and 9-1/2" Clutch. 2.25L and 2.6L NADA.Also used on Front Output of LT230 for Defend...

OEM NTN Clutch Release Bearing Series 1 to 2A, 1948-71Used for both 9" and 9-1/2" Clutch. 2.25L and 2.6L NADA.Also used on Front Output of LT230 fo...

Clutch Release Bearing. Series 3, 71-84, Defender, Range Rover Classic, Discovery 1,

OEM NSK Clutch Release Bearing Series 3, 1971-84. Land Rover 90/110, Defender, Discovery 1, Range Rover Classic.

Master Clutch Cylinder For 88" and 109", Late Series 2a, (1969-71 North American Standard), and Series 3 (1971-84). Land Rover 90/110/130 and Defen...

Clutch Slave CylinderSeries 2 and 2A, 1958-71Mounts on the Right-Hand side of the transmission. For the later Series 3 Slave Cylinder, see CC-59123...

Clutch Slave Cylinder Assembly Series 3 1971-1984. Also, for LT77 (Land Rover 90/100 and Defender from 1984 to 1993. Series 3 2.25L requires Hose C...

Clutch Slave Cylinder OEM TRW Series 3 1971-84, (Slave is on the Left Hand side of the transmission), Land Rover 90/110 4 cylinder and Defender LT7...

Clutch Slave Cylinder Repair Kit for either 266694 or 591231

Copper-Nickel Pipe, (will not rust), with Brass Fittings for use on;Series 2 and 2a, 1958 to 1971 with separate Brake/Clutch Reservoir Canister.1/...

Copper Nickel Pipe, Clutch Master Cylinder to Flex Hose, Left Hand Drive 1958-71. 1/4" Copper-Nickel Pipe, (will not rust), with Brass Fittings for...

Copper Nickel Pipe, Clutch Master to Flex Hose, LHD Series 3 1971-841/4" Copper-Nickel Pipe, (will not rust), with Brass Fittings for use on;88" an...

Copper Nickel Pipe, Clutch Flex Hose to Slave, LHD/RHD Series 3 1971-841/4" Copper-Nickel Pipe, (will not rust), with Brass Fittings for use on;88"...

Defender - A Celebration of the Best 4 x 4 Vol 2 From the team at Land Rover Monthly, this 228 page magbook celebrates the Defender including vehic...

Clutch Flex Hose for Series 3 1971-1984 4-Cylinder Engine.

Clutch Flex Hose for Series 3 2.6L 6 Cylinder Engine, 1971-84, and Land Rover 90/100, Defenders with the LT77 Gearbox up to 1994,For Series 3 2.25L...

Shock Absorber Front Standard Duty For Series 1-3, 107" and 109" Includes Required Bushings

Haynes Defender 90/110 Diesel Owners Workshop Manual Covers Land Rover 90, 110 and Defender up to 2007 with 2.25/2.5L, 2.5TD, 200/300Tdi, TD5 Diese...

Land Rover Defender TD5 Workshop Manual 1999-06 Land Rover Defender TD5 1999 - 2006 Model Year. Note: Electrical is a separate manual, see BK-DA3157E.