Series 1 Clutch

9" Clutch Cover Assembly Pressure Plate, 1948-69 Series 1-2a.For the Clutch Friction Plate, see CC-591704.For a Complete Kit with the Cover, Plate ...

9" Clutch Kit with Cover/Pressure Plate, Friction Plate, Bearing and Flywheel Bushing Kit 1948-69 Series 1-2a. Kit Contains CC-591704, CC-591705, C...

9" Clutch Plate for 1948-1969 Series 1-2a.For the Clutch Cover/Pressure Plate, see CC-591705.For a Complete Kit with the Cover, Plate and Flywheel ...

Clutch Release Bearing. Series 3, 71-84, Defender, Range Rover Classic, Discovery 1,

OEM NTN Clutch Release Bearing Series 1 to 2A, 1948-71Used for both 9" and 9-1/2" Clutch. 2.25L and 2.6L NADA.Also used on Front Output of LT230 fo...

Clutch Release Bearing Series 1 to 2A, 1948-71Used for both 9" and 9-1/2" Clutch. 2.25L and 2.6L NADA.Also used on Front Output of LT230 for Defend...

Clutch or Brake Master Cylinder Adapter 3/8"UNF Male to 7/16" UNF Female.Depending on the purpose, you will require BC-233220 Copper Seal and/or BC...

Front or Rear Brake or Clutch Hose, 86/88 107/109, 3/8" UNF.For use on:Series 1 to 2a, Front Brake, Left or Right, 86/88" SWB or 107/109" LWB, fro...

Front or Rear Brake Hose for Series 1 80" 1948-1953 7/16" UNF. For use on; Series 1 80" Front Left or Right, and Rear from 1948 to 1953. Also used ...

Gasket Paper for Clutch Withdrawal Housing. For Series 1 to Series 2a, 1948 to 1962, up to and including Gearbox to Suffix A. AKA EG-90213663. For ...

Clevis Pin for Clutch Cross-Shaft Series 1-2a For Series 1 to 2a, 1948-71. For Complete Kit with washer and cotter pin, see CC-536803KIT (linked be...

Clevis Pin with Washer and Cotter Pin for Clutch Cross-Shaft Series 1-2a. For Series 1 to 2a, 1948-71. Supersedes CC-240191.

Oil Seal for Clutch Cross-Shaft Series1 RHD and Series 2/2a Left- or Right-Hand Drive; 1948-71. For the Series 1 LHD Oil Seal, see CC-219988 (linke...

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.

Lock Nut for Brake Hose 7/16". Series 1 48-53, Series 2, 2a, 3, Land Rover 90/110, Defender Clutch Hose.

Lock Washer Shake-Proof Int Tooth 7/16" for Series 1 Brake Hose & Series 2, 2a, 3 Clutch Hose.

Dust Cap for Wheel Cylinder or Clutch Slave Bleed Screw pn: BB-556508. You are purchasing 1, not 10 as shown in the photo.

Bleed Screw for Wheel Cylinders, Series 1-3 1954-84, and 2/2a Clutch Slave.

Pair of Rubber Grommets and Felt Seals for Series 1 Pedals,For the Brake and Clutch.

Pilot or Spigot Bushing for Flywheel. Series 1-3, 1948 through to end of TD5, Defender, Discovery 2Supersedes 8566L.

Clutch Alignment Tool Series 1-3 for 9" & 9.5" Clutch Plates

Spherical Bearing Cover for Clutch Cross Shaft and Left-Hand Drive Hand Brake. Series 1 to 3. Typically, 2 Required.

Grommet for Bell Housing Clutch Shaft Series 1-2a 1952-67 Up to Gearbox Suffix D April 1967. For the later Grommet, see BG-553262 (linked below).

Blanking Plug/Grommet for Bell HousingSeries 1, 2 and 2a to 1963

Oil Seal for Clutch Cross-Shaft Series 1 Left Hand Drive, 1948-58

Spring for Clutch Pedal Return Series 1 1954-58

Spherical Bearing for Clutch CrossShaft and HandBrake.For Series 2/2a Clutch Cross Shaft and Left Hand Drive HandBrake Lever up to Suff C, (1948-Ap...

Felt Ring for Hand Brake and Clutch Cross-Shaft Bearings.For Series 2-2a Clutch, (2 Required), and Series 1-2a Left Hand Drive Handbrake Lever Shaf...

Bushing for Left-Hand Drive Clutch Pedal Shaft or Right-Hand Drive Brake Pedal Shaft.For Series 1, 1954-58.

Bushing for Left-Hand Drive Brake Pedal Shaft or Right-Hand Drive Clutch Pedal Shaft.For Series 1, 1954-58.

Washer Special for Clutch Clevis Pin & Other Uses.Supersedes CC-10882.

Locker Plate for Flywheel. For Series 1 1.6L and 2.0L, 3 are Required, 1948-58. For Series 2 to 3, 2.25L 3 Bearing and 2.6L, 3 are Required, 1958-8...