Series 1 Drivetrain

Drive Flange Gasket Front 1948-84 or Rear 1958-1984

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Gasket for Rover Differential, Front or Rear.For Series 1-3, Range Rover Classic 1970-95, Discovery 1 1989-98, Discovery 2 1999-04, Defender Front...

Hub Oil Seal.Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full float axles from 1957 to...

Hub Lock Washer. For Series 1-3, the whole run from 1948 through 1984. For Land Rover 90/110 and Defender Front Axles to VIN: KA930455, (1993) and ...

Solid Copper Washer for Filler/Level Plugs on Rover Differentials.For Series 1-2a. Also listed for some Gearbox and Transfer Case Drain plugs..Fits...

PropShaft Rubber Gaitor and Clamps Series 1-3 PAIR

Pinion Oil Seal for Rover Differential Front or Rear OEM For Series 1-3 1950-84l Supersedes AF-217507, AF-561360.

Oil Seal for End of Front Axle Casing 1948-1984 Series 1-3

Gasket Paper for Stub Axle Rear.For Series 1 through 3, from 1957 to the end of 1984.

Hub Bearing and Oil Seal Repair Kit. Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully Floating Axles on 109", and 88" with the optional full ...

Slotted Drain Plug Tool for Series, Defender, and RRC.Uses a 19mm or 3/4" Socket or Wrench.For use on the Slotted Drain Plug, AF-235592.So much eas...

Lock Nut for Hub Bearing Front or Rear.For Series 1-3, Defender, Discovery 1 and RRC, from 1948 through to 1998.OEM Quality.Supersedes AD-217355, A...

Gasket for Stub Axle to Swivel Hub Front, Series 1 to 3, 1954-84

Corteco OEM Hub Oil SealFits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full float axles f...

Corteco Pinion Oil Seal Rover Differential Front or Rear.For Series 1-3 1950-84Supersedes AF-217507, AF-561360.

Distance Piece Collar for Stub Shaft Front or Rear Axle Race for Hub Seal. OEM. Series 1-3 upto 1980 Series 1 Front Only up to 1956.

Castle Nut for Halfshaft, Output Shaft and Differential Pinion.Requires Cotter Pin AD-PS608101L and Flat Washer AD-571922.

Copper Washer/Seal for Swivel Housing Drain Plug. For Series 1-3, Discovery 1, Range Rover Classic, Land Rover 90/110 and Defenders up until 1994. ...

Bolt for Rear Propshaft both ends, and Front Propshaft to Differential.Series 1, 1948-58, Requires 8 for the Front and 1950-58 Requires 4 for the R...

Locker for Stub Axle to Swivel Housing and Rear Brake Back Plate for every Series Truck.Supersedes AD-232416.

Prop Shaft Rubber Gator and Clamps. All Series trucks and Early Defenders. For a Pair of these, see AP-276484PR (linked below left) For the later D...

Gasket Paper for Swivel Hub to Axle Case 1948-1984

Gasket Paper for Rover Differential Oil Seal Retainer For Series 1 and some Series 2/2a's, 1950-63 Note: CHECK Your Differential - This is for Prot...

Cotter Pin for Halfshaft Nut, Rover Differential Flange, and Output Shaft. OEM. Note: You are purchasing 1, not 10 as shown in the photo.

Axle Breather Valve Series 1-3 1948-84, and Range Rover Classic.

Set of 20 Wheel Nuts 15/16" Wide Series 1, 2, and 2A, 1948-69 Double-End.For a Set of 20 of the Later 1-1/16" Wheel Nuts, see AW-576103-20.

Oil Seal for End of Front Axle Casing Series 1-3 1948-1984 OEM Cortego

Key Washer for Hub Bearing Series 1 Front, Series 2-3 Front & Rear. OEM.

Universal Joint for Series 1 to Some Early Series 2a, 1948-64.Greasable. 2-15/16" (75mm) Across the yoke.Measure before you buy please.

Hub Oil Seal, Leather and Metal. For those that like to keep things more original.Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating A...

Mud shield for Front or Rear Rover Differential OEM

Bearing for Half-Shaft Front 1954-1984 Series 1-3

GKN OEM Universal Joint for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Joint Washer Fiber for Fill or Drain Plug on Rover Differentials. For Series 1-2a. Notes:1.05" ID 1.5" OD. For use with AF-533358 (linked below lef...

Hub Bearing and Oil Seal Kit OEM Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full floa...

Inner Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Outer Hub Bearing, see AD-RTC3426. For a complete kit of be...

Drive Flange Member 10-Spline Series 1-3 1948 to June 1980.

Locker Plate for Swivel Pin Series 1-2a 1948-1962 3/8" StudsYou are purchasing 1, not 10 as shown in the photo.4 Required per Side, 8 per Axle.

Drive Flange for Differential 4 Spline Type Rover Differential.Uses Castle Nut AD-3259 and Cotter Pin AD-PS608101L (linked below). You might need a...

Brass Drain Plug for Differential, Fuel Tank or Transfer Case.For Series 1-3.Large Slotted Type. Requires Copper Washer GT-FRC4809.For a proper too...

AVM Free Wheeling Manual Locking Hubs 10-SplineFor Series 1 through 3, to 1980 with 10-Spline Hubs.They're Back Baby! Easy to install, even easier ...

Propshaft, (Drive Shaft), Front for Series 1-3 4 Cylinder 1956-84.Fits Series 1 88" and 109", 1956-58.Fits Series 2-3 88" and 109" 4 Cylinder, (Not...

Outer Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Inner Hub Bearing, see AD-RTC3416 (linked below left). For ...

NTN Inner Hub Bearing Series 1 Front, Series 2, 2A and 3, Front and Rear up to 1980. For Outer Hub Bearing see AD-RTC3426G (linked below left) For ...

NTN Outer Hub Bearing Series 1 Front, Series 2/2A/3 Front and Rear up to 1980. For Inner Hub Bearing see AD-RTC3416G (linked below left) For a comp...

Washer for Half Shaft.Fits the Front and Rear of Series 1-3 10 Spline Axles, (not Series 1 semi-float rear axle). Also for the Transfer Case Output...

Hub Oil Seal - Metal and Rubber, Series 1 Rear Axle 1948-58.Series 1 with Semi-Floating Rear Axle Only.