Series 1 Drivetrain

Gasket Paper for Swivel Hub to Axle Case 1948-1984

Universal Joint for Series 1 to Some Early Series 2a, 1948-64.Greasable. 2-15/16" (75mm) Across the yoke.Measure before you buy please.

Gasket Paper for Rover Differential Oil Seal Retainer For Series 1 and some Series 2/2a's, 1950-63 Note: CHECK Your Differential - This is for Prot...

Oil Seal for End of Front Axle Casing Series 1-3 1948-1984 OEM Cortego

Set of 20 Wheel Nuts 15/16" Wide Series 1, 2, and 2A, 1948-69 Double-End.For a Set of 20 of the Later 1-1/16" Wheel Nuts, see AW-576103-20.

Key Washer for Hub Bearing Series 1 Front, Series 2-3 Front & Rear. OEM.

Hub Oil Seal, Leather and Metal. For those that like to keep things more original.Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating A...

Bearing for Half-Shaft Front 1954-1984 Series 1-3

GKN OEM Universal Joint for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Hub Bearing and Oil Seal Kit OEM Fits Series 1, 1948 to 58, Front Axle. Fits Rear Fully-Floating Axles on 109", and 88" with the optional full floa...

Inner Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Outer Hub Bearing, see AD-RTC3426. For a complete kit of be...

Mud shield for Front or Rear Rover Differential OEM

Drive Flange for Differential 4 Spline Type Rover Differential.Uses Castle Nut AD-3259 and Cotter Pin AD-PS608101L (linked below). You might need a...

Brass Drain Plug for Differential, Fuel Tank or Transfer Case.For Series 1-3.Large Slotted Type. Requires Copper Washer GT-FRC4809.For a proper too...

Joint Washer Fiber for Fill or Drain Plug on Rover Differentials. For Series 1-2a. Notes:1.05" ID 1.5" OD. For use with AF-533358 (linked below lef...

Outer Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Inner Hub Bearing, see AD-RTC3416 (linked below left). For ...

Propshaft (Drive Shaft) Front or Rear.Fits Series 1 80" Front, 1948-53.Fits Series 1 86" and 107" Front, 1954-55.Fits Series 1 86" and 88" Rear, 19...

Drive Flange Member 10-Spline Series 1-3 1948 to June 1980.

Locker Plate for Swivel Pin Series 1-2a 1948-1962 3/8" Studs 4 Required per Side, 8 per Axle. You are purchasing 1, not 10 as shown in the photo.

Hub Oil Seal - Metal and Rubber, Series 1 Rear Axle 1948-58.Series 1 with Semi-Floating Rear Axle Only.

AVM Free Wheeling Manual Locking Hubs 10-SplineFor Series 1 through 3, to 1980 with 10-Spline Hubs.They're Back Baby! Easy to install, even easier ...

Propshaft, (Drive Shaft), Front for Series 1-3 4 Cylinder 1956-84.Fits Series 1 88" and 109", 1956-58.Fits Series 2-3 88" and 109" 4 Cylinder, (Not...

NTN Inner Hub Bearing Series 1 Front, Series 2, 2A and 3, Front and Rear up to 1980. For Outer Hub Bearing see AD-RTC3426G (linked below left) For ...

NTN Outer Hub Bearing Series 1 Front, Series 2/2A/3 Front and Rear up to 1980. For Inner Hub Bearing see AD-RTC3416G (linked below left) For a comp...