Series 1 Drivetrain

Drive Flange for Differential 4 Spline Type Rover Differential.Uses Castle Nut AD-3259 and Cotter Pin AD-PS608101L (linked below). You might need a...

Brass Drain Plug for Differential, Fuel Tank or Transfer Case.For Series 1-3.Large Slotted Type. Requires Copper Washer GT-FRC4809.For a proper too...

Joint Washer Fiber for Fill or Drain Plug on Rover Differentials. For Series 1-2a. Notes:1.05" ID 1.5" OD. For use with AF-533358 (linked below lef...

Outer Hub Bearing For Series 1 Front, Series 2, 2A and 3 Front and Rear up to 1980. For Inner Hub Bearing, see AD-RTC3416 (linked below left). For ...

Propshaft (Drive Shaft) Front or Rear.Fits Series 1 80" Front, 1948-53.Fits Series 1 86" and 107" Front, 1954-55.Fits Series 1 86" and 88" Rear, 19...

Drive Flange Member 10-Spline Series 1-3 1948 to June 1980.

Locker Plate for Swivel Pin Series 1-2a 1948-1962 3/8" Studs 4 Required per Side, 8 per Axle. You are purchasing 1, not 10 as shown in the photo.

Hub Oil Seal - Metal and Rubber, Series 1 Rear Axle 1948-58.Series 1 with Semi-Floating Rear Axle Only.

AVM Free Wheeling Manual Locking Hubs 10-SplineFor Series 1 through 3, to 1980 with 10-Spline Hubs.They're Back Baby! Easy to install, even easier ...

Propshaft, (Drive Shaft), Front for Series 1-3 4 Cylinder 1956-84.Fits Series 1 88" and 109", 1956-58.Fits Series 2-3 88" and 109" 4 Cylinder, (Not...

NTN Inner Hub Bearing Series 1 Front, Series 2, 2A and 3, Front and Rear up to 1980. For Outer Hub Bearing see AD-RTC3426G (linked below left) For ...

NTN Outer Hub Bearing Series 1 Front, Series 2/2A/3 Front and Rear up to 1980. For Inner Hub Bearing see AD-RTC3416G (linked below left) For a comp...

Washer for Half Shaft.Fits the Front and Rear of Series 1-3 10 Spline Axles, (not Series 1 semi-float rear axle). Also for the Transfer Case Output...

Universal Joint, (U-Joint), for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Bushing for Front Half-Shaft Series 1 and Early 2/2a Stub Axle.

Filler Plug for Swivel Housing Series 1-3. Also, for the Transfer Case Oil Level Plug Gearbox Suffix B on; 1/2" BSP.

Bearing for Differential Inner Pinion-EndSeries 1-2a to 1964. Up to Axle Suffix A Inclusive. For later Differential Inner Bearing see AF-539706.

Bearing for Half-Shaft Front Series 1-3, 1954-1984.OEM Made in Spain.

Distance Piece for Half-Shaft Front (Bearing Holder) for Series trucks between 1954 through to the end in 1984.

Outer Pinion Bearing Front or Rear Rover Differential. Series 1 to 2A, 1948-64. Up to Axle Suffix A Inclusive. For later Diff Outer Bearing see AF-...

Flange for Propshaft U-Joint Series 1-2a, 1948-64

Propshaft Rear Hardy-Spicer.For Series 1/2/2a 107" and 109", 4 Cylinder Models,1956-71. Supersedes AP-241256, AP-533719 and AP-553002.

Grease Nipple for PropShaft S1-3 80/86/88/107/109 '48-84 1/4"

Oil Seal for Salisbury Differential Pinion up to 1998 (to VIN: WA159806), Genuine Leather OEM. For later, 1999, VIN: XA159807 on, see AF-STC4401 (l...

Bearing for Differential Taper-Roller Carrier Bearing.For Series 1-3, 2 Required Typically.OEM NTN

Collar for Semi-Float Rear Axle Halfshaft Bearing.For Series 1. 1948-58.

Bearing Grease 20ml Sachet for Hub Bearings

Hub Bearing for Semi-Float Rear Axle Series 1, 1948-58. Semi-Float is determined by the Drive Flange and Axle Shaft being one assembly, as seen in ...

Circlip for Universal Joints. Fits all Series1-3. 1948-84.

Shim for Differential Pinion Bearing Inner 0.005" Early Land Rover Diff.Series 1 to 2a, 1948 to 64 approximately. New Old Stock.

Distance Piece for Bearing on Semi-Floating Rear Axle Hub.For Series 1, 1948-58.This is the Impossible to Find Spacer within the Hub that sets the ...

Special Bolt Long BSF for Rover Differential in Axle Case.Series 1-2a.3/8"BSFx 1-3/4" Hex Fully-Threaded. Typically 6 Required.For the Matching BSF...

Swivel Hub Lock Stop Plate Series All

Series 1 Rear Fully Floating Half Shaft Left Hand Axle Shaft. For Series 1 88 and 109" Full-Floating Axles fitted to all 109 Models from 121704770 ...

Shim for Pinion Bearing Inner 0.020"Early Land Rover Differential up to end of Axle Suffix A, Feb 1964.

Shim for Pinion Bearing Inner 0.005" Early Land Rover Differential Axle Suff-A.