Series 1 Drivetrain

Washer for Half Shaft.Fits the Front and Rear of Series 1-3 10 Spline Axles, (not Series 1 semi-float rear axle). Also for the Transfer Case Output...

Universal Joint, (U-Joint), for Front Half Shaft.For Series 1-3, from 1953 to '84.Supersedes AD-242521, AD-GUJ118, AD-RTC5964.

Bushing for Front Half-Shaft Series 1 and Early 2/2a Stub Axle.

Bearing for Differential Inner Pinion-EndSeries 1-2a to 1964. Up to Axle Suffix A Inclusive. For later Differential Inner Bearing see AF-539706.

Bearing for Half-Shaft Front Series 1-3, 1954-1984.OEM Made in Spain.

Distance Piece for Half-Shaft Front (Bearing Holder) for Series trucks between 1954 through to the end in 1984.

Outer Pinion Bearing Front or Rear Rover Differential. Series 1 to 2A, 1948-64. Up to Axle Suffix A Inclusive. For later Diff Outer Bearing see AF-...

Flange for Propshaft U-Joint Series 1-2a, 1948-64

Filler Plug for Swivel Housing Series 1-3. Also, for the Transfer Case Oil Level Plug Gearbox Suffix B on; 1/2" BSP.

Grease Nipple for PropShaft S1-3 80/86/88/107/109 '48-84 1/4"

Oil Seal for Salisbury Differential Pinion up to 1998 (to VIN: WA159806), Genuine Leather OEM. For later, 1999, VIN: XA159807 on, see AF-STC4401 (l...

Bearing for Differential Taper-Roller Carrier Bearing.For Series 1-3, 2 Required Typically.OEM NTN

Collar for Semi-Float Rear Axle Halfshaft Bearing.For Series 1. 1948-58.

Bearing Grease 20ml Sachet for Hub Bearings

Hub Bearing for Semi-Float Rear Axle Series 1, 1948-58. Semi-Float is determined by the Drive Flange and Axle Shaft being one assembly, as seen in ...

Circlip for Universal Joints. Fits all Series1-3. 1948-84.

Shim for Differential Pinion Bearing Inner 0.005" Early Land Rover Diff.Series 1 to 2a, 1948 to 64 approximately. New Old Stock.

Distance Piece for Bearing on Semi-Floating Rear Axle Hub.For Series 1, 1948-58.This is the Impossible to Find Spacer within the Hub that sets the ...

Swivel Hub Lock Stop Plate Series All

Series 1 Rear Fully Floating Half Shaft Left Hand Axle Shaft. For Series 1 88 and 109" Full-Floating Axles fitted to all 109 Models from 121704770 ...

Series 1 Rear Fully Floating Half Shaft Right Hand Axle, (Short), Shaft. For Series 1 88 and 109" Full-Floating Axles fitted to all 109 Models from...

Shim for Pinion Bearing Inner 0.020"Early Land Rover Differential up to end of Axle Suffix A, Feb 1964.

Shim for Pinion Bearing Inner 0.005" Early Land Rover Differential Axle Suff-A.

Bolt 3/8" BSF by 1" Long.Front Stub Axle to Swivel Hub, Front Brake Plate to Swivel, Set Bolt for Rover Differential Crown Wheel.

Propshaft Rear Hardy-Spicer.For Series 1/2/2a 107" and 109", 4 Cylinder Models,1956-71. Supersedes AP-241256, AP-533719 and AP-553002.

Differential Crown Wheel and Pinion for Series 1-3 1950-84.

Differential Guard for Rover Axle 2-Bolt Galvanized.Series 1-3, Defender Rover Axle, Discovery 1, and Range Rover Classic.

Oil Seal for Salisbury Differential Pinion up to 1998 (to VIN: WA159806), Rubber. For later, 1999, VIN: XA159807 on, see AF-STC4401 (linked below).

Brass Oil Filler/Level Plug Hex-Head for Rover Differential. For Series 1, 2, and 2a up to VIN Suffix G, (April 1966), and the V8 4-Speed Gearbox. ...

Bearing for Differential Taper-Roller Carrier Bearing.For Series 1-3, 2 Required Typically.

Drain Plug for Swivel Housing. For Series 1-3, Discovery 1, Range Rover Classic, Land Rover 90/110 and Defenders up until 1994. For required Copper...

Locker for Differential Crown Wheel and Pinion Bolts

Shim for Pinion Bearing Flange-End 0.010" Early Land Rover Differential.

Sleeve for Rear Hub Seal Series 1 Semi-Float Rear Axle, 1948-58. Special Order Item, ships to you in 2 to 3 weeks.

Stub Shaft Outer Series 1-3 86/88"-1954-81 107/109"-1954-71 Note: This is a Special Order Item. Ships to you in 2 to 3 weeks.

Bolt for PropShaft Rear to Transfer Case for Series 1, 1948-58.3/8"UNF x 1 3/16" OEM

Special Bolt Long BSF for Rover Differential in Axle Case.Series 1-2a.3/8"BSFx 1-3/4" Hex Fully-Threaded. Typically 6 Required.For the Matching BSF...

Outer Pinion Bearing Front or Rear Rover Differential. NTN OEM, Made in Japan. Series 1 to 2A, 1948-64. Up to Axle Suffix A Inclusive. For later Di...

Service Kit for Fairey Free Wheeling Hubs Pair.Does either the 10 or 24 Spline Hubs.

Thrust Washer for Early Rover Differential .040" (07905)

Thrust Washer 0.050" for Rover Differential

Differential Guard for Rover Axle 2-Bolt Zintex.Series 1-3, Defender Rover Axle, Discovery 1, and Range Rover Classic.

Differential Pinion (Spyder Gear) Rover Series 1-3 1948-75

Differential Spindle (Spyder Gear) Rover Series 1-3 1948-73 OEM

Differential Wheel (Spyder Gear) Rover Series 1-3 1948-75