Series 1 Engine

Bushing for Inlet Valve Rocker.For 1.6L and 2.0L Series 1, 1948-58.Land Rover Genuine.

Exhaust Valve Seat Oversize .005.For Series 1 1.6L and 2.0L, 1948-58, and Series 2a 2.6L 6 Cylinder.

Spring Oil Pressure Release Valve Series 1 1954-58

Circlip for Adjuster Arm to Pivot Pin Series 1 1.6L and 2.0L Gas Engine.Supersedes EP-09129 and EP-9129.

Circlip for Timing Chain Idler Wheel.For Series 1 1.6L, 2.0L 1948-58.Supersedes EP-09128 and EP-9128.

Ball for Oil Pump Release Valve on Series 1 1948-58 and 2.6L 6 Cylinder.

Spring for Timing Pawl Chain Tensioner Series 1 1.6L and 2.0L Gas Engine.

Nut Hex 5/16" BSF Narrow Various Uses.For Series 1 1.6L and 2.0L Tappet Adjuster Screws, EP-506812 and EP-506818.

Tappet Adjusting Screw Exhaust with Cap.For Series 1 1.6L and 2.0L, 1948-58.Includes Cap EP-212160 and Circlip EP-212161.Requires Lock Nut BN-2842,...

Tappet Adjusting Screw Inlet.For Series 1 1.6L and 2.0L, 1948-58.Requires Lock Nut BN-2842, (These are BSF Thread).Land Rover Genuine. NOS. Superse...

Tappet Adjuster Screw.For Series 1 and 2, 2.0L Diesel, Series 2-3 2.25L Gas or Diesel.Typically 8 Required. Each Requires Half-Nut BN-NT605061L.

Lock Washer for Timing Chain Damper.For Series 1 2.0L, and Series 2-3 2.25L and 2.6L Gas.Two Typically Required.Supersedes EP-278769.

Steel Ball for Oil Pump Relief Valve.For Series 1 2.0L Diesel and Series 2-3 2.25L Gas or Diesel.

Locker Plate for Oil Feed Bolt to Distributor.For Series 1 1.6L and 2.0L, and Series 2a 2.6L 6 Cylinder.

Locker Plate for Cam Shaft Bearings.For Series 1 1.6L and 2.0L, 1948-58.Typically 4 Required to Fix the Camshaft Bearings to the Cylinder Head.New ...

OEM Banjo Bolt for Oil Pipe from Block to Cylinder Head and Various Uses.Series 1 1.6L and 2.0L, 1948-58, (1 Required).Series 2-3, 2.25L 1958-84, (...

Bushing for Idler Gear in Oil Pump Series 1 1.6L and 2.0L, 1948-58.aka: EP-9049.

Gasket Cork for Rear Camshaft Cover.For Series 1 1.6L and 2.0L 1948-58.

Fiber Washer for Rocker Cover Bolts Series 1 1948-58.3 Required.

Cork Packing Seals for Rear Main Bearing (Pair).For Series 1 2.0L 1955-58 and Series 2a 2.6L 6 Cylinder.Supersedes EG-7959, EG-265653, EG-267653 a...

Exhaust Rocker Arm Bushing All Diesel Engines upto 1990 (Not Tdi).Fits Series 1 to 3, 2.0L and 2.25L Diesel, Defender 2.5L Naturally Aspirated and ...

Inlet Rocker Arm Bushing All Diesel Engines upto 1990 (Not Tdi). Fits Series 1 to 3, 2.0L and 2.25L Diesel, Defender 2.5L Naturally Aspirated and 2...

Bushing for Oil Pump Idler Gear.For Series 2-3 1960-84.Note: Series 2, 1958-59 Engines Have a Different Idler Gear, see EP-237884.This Bushing is a...

Main Bearing Set .010 Under Size 2.25L Gas Series 2 1958-61 and Series 1-2, 2.0L Diesel.Note: These are NOS specific to the Series 2, 1958-61 2.25L...

Seal for Side Rocker Cover Nut Series 1, 1.6/20L 1948-53

Camshaft for Series 1-2a, 2.0L Diesel and Series 2a-3, 2.25L Diesel up to 1983,

Camshaft Bearing Front for 4 Cylinder Engines, 1958-98, OEM.For 2.0L Diesel, 2.25L Gas or Diesel, 2.5NA, 2.5TD, 200Tdi and 300Tdi.Un-Split Ring Sty...

Camshaft Bearing Rear 4 Cylinder Engines, 1958-98, OEM.<.p>For 2.0L Diesel, 2.25L Gas or Diesel, 2.5NA, 2.5TD, 200Tdi and 300Tdi.Un-Split Rin...

Exhaust Valve for 2.0L and 2.25L Diesel Series 1-3For Inlet Valve see EP-ERC6795 (linked below).Supersedes EP-247569, EP-513481, and EP-ERC6794.Not...

Ring Gear for Flywheel on 2.0L Diesel.For Series 1 & 2, 1957 to 1961.New Old Stock - Made in the UK.

Woodruff Key for Chainwheel to Camshaft.Series 1-3, 1.6 and 2.0L Gas, 2.0L Diesel, 2.25L Gas or Diesel.Defender 2.5L Gas or Diesel, 2.5Turbo Diesel...

Nut 2BA Thread for Accelerator Rod Ball Joints and Various Other Uses.Supersedes FS-2247 and FS-3823.Note: You are purchasing 1, not 10 as shown in...

Ball Joint Assembly for 2BA Threaded Accelerator Rods Series1-3, and Defender V8 Requires FS-RTC608 2BA Nut for Locking in Position (linked below) ...

Heater/Glow Plug for 2.0L & 2.25L Diesel Engine Series 1-3, 1956-84, 3 and 5 main Bearing up to Engine Serial Number 36623971B. For a Kit that ...

Head Gasket 2.25L Dsl, 2.5D, 2.5TD (Not Tdi)

Valve Guide Inlet Diesel 2.0L and 2.25L Series 1-2a Fits Diesels from 1956 through 1968.For O-Ring Seal see EP-247186.Supersedes EP-272206

Lock Washer for Starting Dog on Crank Series 1-3 1948-84 For 3 Bearing Engines

Starting Handle Dog for 3 Bearing Engines 1.6L, 2.0L, 2.25LFor Series 1, 2, 2a and 3, 3-Bearing Engines.Requires EP-247771 Lock Washer, (Not Includ...

Ring Gear for Flywheel Series 1, 2.0L (1955-58 Spreadbore) Series 2-3, 2.25L and 2.6L Gas

Carburetor Linkage Ball Joint for Series 1 Solex 32PBI 1948-58Note: 1/4" BSF Male and 1/4" BSF Female ends.Requires BN-3819 1/4" BSF Nut for Lockin...

Extension for Drain Tap on Engine Block Series 1 1948-58. New oil stock, goo included.

Valve Spring Cap for Series 1 1.6L and 2.0L 1950-58 Inlet Valves, Exhaust Valves from Engines 06106720, and Series 2a 2.6L 6 Cylinder Exhaust Valves.

Timing Chain Wheel for CamshaftSeries 2-3, 2.0L Diesel, 2.25L Gas or Deisel, 2.6L 6 Cylinder Gas.Requires Key EP-9210.

Connecting Rod "Big End" Bearing Set .010 US.1955-58 Series 1 2.0L Spreadbore Engine.New Old Stock.

Connecting Rod Bearing Set .040 US.Series 1 1955-58 2.0L Gas Spreadbore Engine.New Old Stock.

T/Washer .0025 for Crankshaft 2.0L 1955-58 & Salisbury Diff