Series 2 2a 3 Drivetrain

Thrust Washer 0.050" for Rover Differential

Thrust Washer for Early Rover Differential .040" (07905)

Slotted Drain Plug Tool for Series, Defender, and RRC.Uses a 19mm or 3/4" Socket or Wrench.For use on the Slotted Drain Plug, AF-235592.So much eas...

Hub Oil Seal Series 3 mid-1980on, Defender to '93, RRC to '85.OEM CortecoDefender up to VIN KA930455, (1993), up to Axle No 20L13358B RHS, up to Ax...

Bearing for Differential Inner Pinion-EndSeries 1-2a to 1964. Up to Axle Suffix A Inclusive. For later Differential Inner Bearing see AF-539706.

Bolt 3/8" BSF by 1" Long.Front Stub Axle to Swivel Hub, Front Brake Plate to Swivel, Set Bolt for Rover Differential Crown Wheel.

Special Stud Long UNF for Rover Differential in Axle Case.This is the 3/8" UNF x 1-1/4" Long Push-Through Stud, considered the "Shorter" Stud. 4 Ty...

Special Stud Long UNF for Rover Differential in Axle Case.This is the 3/8" UNF x 1-3/4" Long Push-Through Stud, considered the "Longer" Stud. 6 Typ...

Service Kit for Fairey Free Wheeling Hubs Pair.Does either the 10 or 24 Spline Hubs.

Joint Washer Fiber for Fill or Drain Plug on Rover Differentials. For Series 1-2a. Notes:1.05" ID 1.5" OD. For use with AF-533358 (linked below lef...

Sealing washer designed for differential and gearbox drain plugs. Positioned between the plug and the housing, it ensures a leak-tight seal across ...

Shim for Pinion Bearing Inner 0.005" Early Land Rover Differential Axle Suff-A.

Shim for Pinion Bearing Inner 0.020"Early Land Rover Differential up to end of Axle Suffix A, Feb 1964.

Brass Drain Plug for Differential, Fuel Tank or Transfer Case.For Series 1-3.Large Slotted Type. Requires Copper Washer GT-FRC4809.For a proper too...

Filler Plug Screw for Drive Member Early Series 2-2a.Note: This screw requires Copper Seal EP-232038 (linked below).

Outer Pinion Bearing Front or Rear Rover Differential. NTN OEM, Made in Japan. Series 1 to 2A, 1948-64. Up to Axle Suffix A Inclusive. For later Di...

Set of 20 Wheel Nuts 15/16" Wide Series 1, 2, and 2A, 1948-69 Double-End.For a Set of 20 of the Later 1-1/16" Wheel Nuts, see AW-576103-20.

Swivel Hub Lock Stop Plate Series All

Special Bolt Long BSF for Rover Differential in Axle Case.Series 1-2a.3/8"BSFx 1-3/4" Hex Fully-Threaded. Typically 6 Required.For the Matching BSF...

Shim for Differential Pinion Bearing Inner 0.005" Early Land Rover Diff.Series 1 to 2a, 1948 to 64 approximately. New Old Stock.

Half Shaft Front Inner Right Hand 1958-84 Series 2-3. Not for 1-Ton Models. For Left Hand Inner Half-Shaft see AD-276720 (linked below left). For O...

Stub Shaft Outer Series 1-3 86/88"-1954-81 107/109"-1954-71 SPECIAL ORDER: Please note this item is special order and there will be a substantial p...

Shim .005 Pinion Bearing for Salisbury Differential 110 109 OEM

Shim .003 for Pinion Bearing Salisbury Differential OEM

Shim .010 Pinion Bearing Salisbury Differential OEM

Taper Roller Bearing for Differential Carrier. Cone and Cup Set. For ENV Differential Only Forward Control Series 2A and 2B. Genuine Timkin 28580 /...

Drive Flange for Differential 4 Spline Type Rover Differential.Uses Castle Nut AD-3259 and Cotter Pin AD-PS608101L (linked below). You might need a...

Shim for Pinion Bearing Flange-End 0.010" Early Land Rover Differential.

Locker for Differential Crown Wheel and Pinion Bolts

Pinion Bearing Outer for Salisbury Differential Timkin Series and Defender

Bolt Kit Rear Stub Axles to Rover Axle S2/2a (Axle Set)