Series 2 2a 3 Engine

Valve Seal Inlet Guide (O-Ring) 2.25L Gas up to March 1968, Engine Suff K Also on 2.0/2.25L Diesels up to 1968. Land Rover Genuine

Replacement Heater/Glow Plug for 2.25L Diesel Engine 1962-84.For Parallel Wired Glow Plugs, as in the Kit EE-DA1057..

Diaphragm for Crankcase Emissions Vent Control (PCV Valve)For Late Series 2a and Series 3 For the Complete Assembly, see EP-RTC6855 (linked below).

Crankcase Emissions Vent Control (PCV) Assembly For late Series 2a and Series 3. For the Diaphragm Only, see EP-RTC6855DIA (linked below). Supersed...

Fuel Pipe Tank to Pump 88/109 Forward Tank Series 2-3 1958-84 For the Fuel Line that runs from the Pump to the Carburetor, see EF-557432, (for Sole...

Fuel Pipe Tank to Pump 109 Station Wagon Series 2-3. Rear Tank. For the Fuel Line that runs from the Pump to the Carburetor, see EF-557432, (for So...

Fuel Pipe Pump to Zenith Carburetor OEM For Series 3 1972-84, (or conversions from Solex to Zenith or Weber Carburetors). Made in UK You may also n...

Fuel Pipe Short Connecting Fuel Line to Zenith Carburetor For Series 3 1972-84, (or conversions from Solex to Zenith or Weber Carburetors). You may...

Breather Cap on Non-Vented Filler Tube 2.0L/2.25L Series 1-3 with Label.For Non-Ventilated Oil Filler Pipes. Series 1 Engine 26100201, (1952), onwa...

Breather Cap on Rocker Cover 2.0/2.25L Gas Series 1-3. With Label. No Emissions Pipe. Fitted to Engines up to Prefix 901 & 904 Suff B. For Ser...

Breather Cap on Diesel Rocker Cover Series 2a/3. Can be used on 2.25L Gas Engines with EGR Tube Required. Note: Emissions Tube is 7/16", larger tha...

Starter Motor for 2.25L Diesel Series 3.

Head Gasket 2.25L Dsl, 2.5D, 2.5TD (Not Tdi)

Connecting Rod Assembly 2.25L Diesel Series 2a through to early Land Rover 90 and 110

Copper Washer for Oil Sump Drain Plug Series 1-3 And for Heater Control Adapter on Series 3 Crushable Copper Seal

Engine Mounting Rubber with Nuts.For Series 2, 2a, 3 Engines, 2.25L and 2.6L, 1958-84.

Gasket for Oil Filter Housing to Block Series 3 2.25L Gas or Diesel, and 2.6L, 1971-85, (See note below). Defender 2.5TD and 200Tdi, 1986-94. Super...

Heater/Glow Plug for 5-Bearing 2.25L Diesel, 2.5L Diesel, and 2.5TD Turbo Diesel.

Heater/Glow Plug for 5-Bearing 2.25L Diesel, 2.5L Diesel, and 2.5TD Turbo Diesel.OEM Bosch/Wellman.

Heater/Glow Plug for 2.0L & 2.25L Diesel Engine Series 1-3, 1956-84, 3 and 5 main Bearing up to Engine Serial Number 36623971B. For a Kit that ...

Washer Flat Valve Cover Dome Nut S2-3 2.25L & Diesel Lines OEM

Ball Joint Assembly for 2BA Threaded Accelerator Rods Series1-3, and Defender V8 Requires FS-RTC608 2BA Nut for Locking in Position (linked below) ...

Bell Crank Rod Assembly Lever to Carburetor Series 2a-3 2.25L March 1963on and 2.6L.Final Connection to Solex, Zenith and Weber Carburetors.

Ball Joint for Carburetor Accelerator Linkage Brass.Series 2-2a 1958-63 (upto Eng-Suff C)This is 1/4"-28 UNF Male and Female. Uses BN-NH604041L 1/4...

Accelerator Control Rod Cross Shaft to Engine Ball-Joint TypeFor 1958 Series 2 with the 2.0L Spreadbore Engine.Threaded 2BA, 2-3/8" Long.See EF-AAU...

Nut 2BA Thread for Accelerator Rod Ball Joints and Various Other Uses.Supersedes FS-2247 and FS-3823.Note: You are purchasing 1, not 10 as shown in...

Gasket Set for Solex Zenith Stromberg 175CD CarburetorFor 2.6L 6Cyl and 3.5L V8

Locker Plate for Timing Chain Wheel to Camshaft. OEM.For Series 1-3, 1948-84

Woodruff Key for Chainwheel to Camshaft.Series 1-3, 1.6 and 2.0L Gas, 2.0L Diesel, 2.25L Gas or Diesel.Defender 2.5L Gas or Diesel, 2.5Turbo Diesel...

Cylinder Head Overhaul Kit for Series 3 1975 on, 2.25L GasEverything needed to do a Valve Job.

Cylinder Head Overhaul Kit for Series 2, 2a, 3 up to 1974, 2.25L GasEverything needed to do a Valve Job.

Otter Switch Choke Warning Light.For Series 2-3 Cylinder Head with Spade-Connector.Located on the Front of the 2.25L Cylinder Head. Activates the C...

2.25 Piston Ring Set per Piston .020 OS Gas For Series 2 through 3, 1958-84

Guides for Rear Main Bearing T-Seals Pair OEM.Required when pressing the seal retainer into place on the Series 2.25L Engine.

Hose for Air Cleaner to Carburetor Elbow on 2.25L and 2.6L With Stainless Steel Clamps - Ready to Install. Series 2 to 3. For the same Hose without...

Temro Thread-In Block Heater 125V 400WFor 2.25L 4 Cylinder Gas and Diesel, and 2.6L 6 Cylinder Gas. Series 2-3Fits in the Rear Threaded Core Plug H...