Series 2 2a 3 Engine

Ball Joint for Accelerator Linkage BrassSeries 2-2a 1958-63 (upto Eng-Suff C)This is 1/4"-28 UNF Male and Female. Uses BN-NH604041L 1/4" UNF Nut fo...

Accelerator Control Rod Cross Shaft to Engine Ball-Joint TypeFor 1958 Series 2 with the 2.0L Spreadbore Engine.Threaded 2BA, 2-3/8" Long.See EF-AAU...

Nut 2BA Thread for Accelerator Rod Ball Joints and Various Other Uses.Supersedes FS-2247 and FS-3823.Note: You are purchasing 1, not 10 as shown in...

Gasket Set for Solex Zenith Stromberg 175CD CarburetorFor 2.6L 6Cyl and 3.5L V8

Locker Plate for Timing Chain Wheel to Camshaft. OEM.For Series 1-3, 1948-84

Woodruff Key for Chainwheel to Camshaft.Series 1-3, 1.6 and 2.0L Gas, 2.0L Diesel, 2.25L Gas or Diesel.Defender 2.5L Gas or Diesel, 2.5Turbo Diesel...

Cylinder Head Overhaul Kit for Series 3 1975 on, 2.25L GasEverything needed to do a Valve Job.

Cylinder Head Overhaul Kit for Series 2, 2a, 3 up to 1974, 2.25L GasEverything needed to do a Valve Job.

Otter Switch Choke Warning Light.For Series 2-3 Cylinder Head with Spade-Connector.Located on the Front of the 2.25L Cylinder Head. Activates the C...

2.25 Piston Ring Set per Piston .020 OS Gas For Series 2 through 3, 1958-84

Guides for Rear Main Bearing T-Seals Pair OEM.Required when pressing the seal retainer into place on the Series 2.25L Engine.

Hose for Air Cleaner to Carburetor Elbow on 2.25L and 2.6L With Stainless Steel Clamps - Ready to Install. Series 2 to 3. For the same Hose without...

Temro Thread-In Block Heater 125V 400WFor 2.25L 4 Cylinder Gas and Diesel, and 2.6L 6 Cylinder Gas. Series 2-3Fits in the Rear Threaded Core Plug H...

Zerostart Temro Lower Radiator Hose Heater 1-1/2" 600Watts.Fits Late Series 2a and Series 3, (1968-84; or, if you replaced your radiator with the l...

Temro Freeze-Plug Engine Heater 400W 120vFits Series 2-3 2.25L Gas or Diesel 3-Bearing Engines. Replaces the Frost/Freeze Core Plug EP-525428. 1-15...

Temro Freeze-Plug Block Heater 400w 120vFits 2.25L 5-Bearing Engine, 2.5L Naturally Aspirated Diesel, 2.5L Turbo Diesel, 200Tdi and 300Tdi.2.06" Di...

Zerostart Temro Lower Radiator Hose Heater 1-1/4" 375Watts.Fits Series 2 2a with original Rad Hoses, (note if car has later Radiator, the hoses wil...

Gasket for Fuel Pump Side Cover to Engine Block2.25L Engine, Series 2-3

Front Crankshaft Pulley for 2.25L 3-Bearing EngineSeries 2a-3 1961-84Gas or Diesel, Single Belt.For Locker Washer see EP-247771 (linked below left)...

Woodruff Key for Crankshaft Timing Gear and Pulley.For Series 1 2.0L Diesel, Series and Defender 2.25L Gas and Diesel, 2.5L Gas and Naturally Aspir...

Hose Connector for Zenith or Weber Carburetor to Air Cleaner Elbow For Series 2a-3 1968on, or earlier if converted to a Zenith or Weber Carb. If yo...

Fuel Pipe from Pump to Early Zenith Carburetor 1969-72 This is only for the early Zenith Carburetors with the Female Nut and Olive on the Carbureto...

Mud Excluder for Front Crank Oil Seal Fits 2.25L Gas or Diesel, and 2.5L Gas. After drilling out the original rivets that hold the Mud Shield in pl...

Exhaust Valve 2.6L 6 Cylinder Euro/NADA NADA Part Number: 512140

Exhaust Valve 2.25L Gas Series 2-3, 1958-81For Standard 3-Bearing Engine.For Inlet Valve see EP-ERC7150 (linked below). For Complete Head Rebuiild ...

Inlet Valve 2.25L Gas Series 2-3, 1958-81 For Standard 3-Bearing Engine. For Exhaust Valve see EP-ERC7151 (linked below left). For Complete Head Re...

Hardened Valve Seat Insert for Exhaust Valve for 2.25L Gas Engine.Series 2 to 3 2.25L Gas and Defender 2.25L and 2.5L Gas.Santana, Made in Spain.

Inlet Valve Late Series 3, 90/110 2.25 & 2.5L Gas, 5-Bearing Engine. For Exhaust Valve see EP-ETC5866 (linked below).

Exhaust Valve Late Series 3, 90/110 2.25 & 2.5L Gas, 5-Bearing Engine.For Inlet Valve see EP-ETC4067 (linked below).

Frost Core Plug 1-7/8" Push-In Cup for 2.0L, 2.25L, and 2.5L Gas or Diesel (Side Plugs)Series 1 2.0L uses 4. Series 2-3 2.25L uses 3.

Frost Core Plug Push-In Cup 11/16" for Cylinder HeadSeries 3 2.25L Gas 1972on, and 2.5L Gas Defender

Frost Core Plug Cup 1-3/8" Various Applications. (Front/Rear Plugs)

Frost Core Plug Push-In Cup for Water Jacket 15/16" All 4-Cylinders to 1994 (Cylinder Head Plug)

Frost Core Plug Cup for Cylinder Block 1-3/4" DiameterVarious uses.

Frost Core Plug Cup for Cylinder Block 1" Diameter All 4 Cylinder Engines to 1994.

Cylinder Block Freeze Plug KitFor Series 2a-3 2.25L Gas or Diesel and Defender 2.5L Gas or Naturally Aspirated Diesel.Note: for Series 3 1972on 2.2...

Mahle Fuel Filter - Diesel 2.25NA, 2.5NA, 2.5TD with Seals

Oil Pressure Gauge Sender for Series 3 Large Bulb Type OEM. Made in Great Britain. New Old Stock. Soon to be a "No Longer Available Part".

Gasket for Inlet Manifold to Phenolic Block and Block to Carburetor or Adapter. For Series 2-3, 1958-84 Two Required for Solex Carburetor, Two Requ...

Gasket for Zenith or Weber Carburetor to AdapterSeries 2a-3.

OEM Valve Seal (Umbrella/Lip-Type) for Inlet Valve.For 2.25L Gas or Diesel, 2.5L Gas or Diesel, and 2.5L Turbo Diesel, 1968 to '90. OEM Viton. You ...

Valve Seal (Umbrella/Lip-Type) for Inlet Valve.For 2.25L Gas or Diesel, 2.5L Gas or Diesel, and 2.5L Turbo Diesel, 1968 to '90. Nitrile.You are pur...

Valve Seal Exhaust (Umbrella/Lip Type).For 2.25L Gas or Diesel, 2.5L Gas or Diesel, and 2.5TD Turbo Diesel. Viton.You are purchasing 1, not 4 as sh...

OEM Viton Valve Seal Exhaust (Umbrella/Lip Type).Made in Great Britain.For 2.25L Gas or Diesel, 2.5L Gas or Diesel, and 2.5TD Turbo Diesel. Viton.Y...

Cylinder Head Gasket Set for V8 Carburetted.For Series 3 Stage 1 109 V8, 101FC, and RRC to1991.With Steel Head Gaskets.For Bottom End Gasket Set, s...

Bottom End Gasket Set for V8 Carbureted. For Series 3 Stage 1 109 V8, 101FC, Discovery 1 to VIN: LA081991 (1994) and RRC non-EFI. For Top End Head ...

Intake to Exhaust Manifold Stud Kit (Studs, Locks, Nuts, and Gasket),For Mounting the Intake Manifold to the Exhaust Manifold on Series 2-3 Gas Eng...

Stud for the Intake Manifold to the Exhaust Manifold,For the 2.25L Gas Engine, Series 2, 2a and 3.4 Required. For a Complete Kit with Bolts, Nuts, ...