Series 2 2a 3 Engine

Gasket For Front Timing Cover Joint. For Series 1-3, 2.0 Diesel, 2.25L Gas or Diesel, and Defender 2.25L Gas, 2.5L Gas or Naturally Aspirated Diese...

Gasket for 7-Stud Water Pump on 4 Cylinder Military Engines.

Bolt Set Hex Cap 5/16" UNC x 5/8" for Various Uses.For Series 2.25L Heat Shield to Manifold.

Torsion Spring for Bell Crank on Zenith Carburetor 1968-84.

Copper Sealing Washer for Series 2-2a 2.25L Tappet Guide Set Bolt, for Series 3 Windscreen Hinge Bolt, early Series 2-2a Drive Member Fill Plug Scr...

L488 Side Lamp Clear Glass Assembly Complete. Single Pole Lamp. For Series 1 through 2a. Requires Bulb LB-10211 (linked below).

Valve Plug (Grub Screw) in Timing Piston 2.25L Gas.For Series 3 2.25L Engine up to Engine SN: 90290283E and 9045259E.

Locating (Grub) Screw for Oil Pump / Distributor Shaft.

2.25L Connecting Rod Gudgeon Pin Bearing

Hose, Breather to Air Intake Elbow 2.25L Gas.For Series 3 North American Standard, and Engine Prefix 901 and 904 Suffix C and D.

Hose Elbow for Emission System, from Carburettor Adapter to Crankcase PCV Vent Control Series 3 up to Suffix C, (August 1974) Note: This is a 2" x ...

Hose Elbow for Crankcase Vent Control to Carburetor Adapter Port. For Some Early Series 3. Note: This is a 3" x 3" Rubber Elbow. Later Series 3 use...

Pipe Adapter for Emission Hose on Carburetor Adapter or Inlet ManifoldFor Late Series 2a and Series 3.You might need the Copper Seal, see CS-243958...

Idler Wheel for Timing Chain.For Series 1-3, 2.0L Diesel, 2.25L Gas and Diesel.

Connecting Rod Assembly 2.25L Gas Series 2 1958-61Note: This is Specifically for the Series 2, 1958-61, Gas Engine. Serial Numbers 151XXXXXX.These ...

Special Bolt to hold Breather Cap on Rocker Cover.For Series 1-3 1956-84.

Engine or Gearbox Mounting Rubber with Nuts for 2.25L Diesel Engine.Series 2-3 Diesel.Sometimes used as a stronger Engine Mount for Gas Engines and...

Gearbox Mounting Rubber with Nuts.Series 1 Engine Mounts from 1954 to 1958 and Series 2/2a/3 Gearbox Mounts from 1958 up through 1984.

Main Bearing Set .010 Under Size 2.25L Gas Series 2 1958-61 and Series 1-2, 2.0L Diesel.Note: These are NOS specific to the Series 2, 1958-61 2.25L...

Bushing for Oil Pump Idler Gear.For Series 2-3 1960-84.Note: Series 2, 1958-59 Engines Have a Different Idler Gear, see EP-237884.This Bushing is a...

Valve Spring Cap for Series 1 1.6L and 2.0L 1950-58 Inlet Valves, Exhaust Valves from Engines 06106720, and Series 2a 2.6L 6 Cylinder Exhaust Valves.

Control Rod for Governor on Series 2a 2.25L Engine Suffix J (1967on).New Old Stock.

Inlet Rocker Arm Bushing All Diesel Engines upto 1990 (Not Tdi). Fits Series 1 to 3, 2.0L and 2.25L Diesel, Defender 2.5L Naturally Aspirated and 2...

Exhaust Rocker Arm Bushing All Diesel Engines upto 1990 (Not Tdi).Fits Series 1 to 3, 2.0L and 2.25L Diesel, Defender 2.5L Naturally Aspirated and ...

Valve Guide for Inlet Valves on 2.6L 6 Cylinder European Version. Not for Series 2a NADA 2.6L.Supersedes EP-504169.New Old Stock.

Cork Packing Seals for Rear Main Bearing (Pair).For Series 1 2.0L 1955-58 and Series 2a 2.6L 6 Cylinder.Supersedes EG-7959, EG-265653, EG-267653 a...

Sealing Washer O-Ring Side Rocker Cover for Series 1 2.0L 1954-58, Speedometer Pinion Sleeve Series 1-3 to 1984 and Series 2a 2.6L Water Pump. Mayb...

Original Cork Gasket for Oil Filter Housing to Block.Series 1 2.0L (Filter Housing to Adapter), Series 2-3, 2.25L and 2.6L.Defender 2.5TD and 200Td...

OEM Banjo Bolt for Oil Pipe from Block to Cylinder Head and Various Uses.Series 1 1.6L and 2.0L, 1948-58, (1 Required).Series 2-3, 2.25L 1958-84, (...

Copper Sealing Washer Crushable for Various Uses. OEM.For Series 1-3 Oil Banjo Bolts, Series 2-3 Oil Pressure Sending Unit, Discovery 1, Discovery ...

Locker Plate for Oil Feed Bolt to Distributor.For Series 1 1.6L and 2.0L, and Series 2a 2.6L 6 Cylinder.

Steel Ball for Oil Pump Relief Valve.For Series 1 2.0L Diesel and Series 2-3 2.25L Gas or Diesel.

Lock Washer for Timing Chain Damper.For Series 1 2.0L, and Series 2-3 2.25L and 2.6L Gas.Two Typically Required.Supersedes EP-278769.

Oil Feed Pipe Block to Cylinder Head OEM. For Series 2-3 2.25 Gas or Diesel, and Defender 2.5L Gas or Diesel. Requires 2x EP-597563 Banjo Bolts and...

Tappet Adjuster Screw.For Series 1 and 2, 2.0L Diesel, Series 2-3 2.25L Gas or Diesel.Typically 8 Required. Each Requires Half-Nut BN-NT605061L.

Castrol GTX Classic 20W50 Conventional Engine Oil 1 Litre Jug.For Series 1 to 3, 1.6L, 2.0L, 2.25L, 2.6L Gas and Diesel Engines.Castrol® GTX® Class...