Series 2 2a 3 Transmission

Layshaft for Gearbox Suffix A, (or No Suffix Letter on Early Gearbox). Series 1 to 2a, 1948 to September 1962. NOTE: This is a Special Order Item, ...

Layshaft Cluster for Series 3 Gearbox Suffix B Only. NOTE: This is a Special Order Item, ships to you in 2 to 3 weeks.

Layshaft for Gearbox Suffix B and C. Series 2a, September 1962 to January 1965. OEM. NOTE: This is a Special Order Item, Ships to you in 2 to 3 weeks.

Gasket for Clutch Withdrawal Housing. Series 2a, 1962 Gearbox Suffix B on to 1971. For the earlier gasket, See EG-213663. For the later Series 3 Ga...

Gearbox Bearing Kit for Series 3, Suffix B on, (September 1972 on), 6-piece set. Includes:GT-55714 Primary Pinion Bearing,GT-1645 Main Shaft Rear B...

Set of 3 Detent Springs for Synchronising Clutch, (Clutch Synchro), Assembly in Gearbox. For Series 1 to 3, 1948-84. 3rd and 4th Gear Synchro. Supe...

Gearbox Case and Top Cover for Series 3 Gearbox Suffix B onwards.Fits Series 3, 4 and 6 Cylinder, Gas or Diesel, from roughly September 1972.New Ol...

O-Ring Seal for Forward Gear Selector Shafts.Land Rover Genuine Part.Series 1 to 3, 1955-84.Typically 2 Required.Supersedes GT-241596, GT-237637.

Stud for Inspection Cover on Flywheel Housing Series 1-3 1956-84.

Bearing for Rear of Main Shaft in Gearbox.For Series1-3 OEM SKF. Made in Italy.

Stop for 2nd Gear Selection Shaft. For Series 1-3, LT76 Gearbox.

Four Wheel Drive Selector Fork for LT76. Series 1-3.Supersedes GT-233397.

Output Shaft Front for Series 1 to 3 1948-84.Supersedes GT-233248.This item is Old New Stock.

Lock Washer for Fairey Overdrive Series 1-3.

Bushing for Selector Fork in Transfer Case.Series 1 to 2a, 1951-66.Typically 2 Required.Supersedes GT-217521.

Spacer Distance Piece for Layshaft 0.405".

Split Ring Retainer for Series Gearbox Layshaft.For Series 1-2a, up to and including Suffix C, 1948-66.

Reverse Gear Shaft for Series 1-2a, 1948-71.For later Series 3 Gearbox Suffix A, see GT-591527; for Series 3 Suffix B onwards, see GT-FRC1813.Note:...

Reverse Gear Idler Shaft for Series 3 Suffix A Gearbox Only, 1971-72.For Earlier, see GT-561962 (SS: GT-06424). For Later Series 3 Suff B onwards s...

Reverse Shaft Series 3 Gearbox Suffix B Onwards.From September 1972. For the Earlier Series 3 Suffix A Gearbox, see GT-591527.Note: This is a Speci...

Inspection Cover Plate Gearbox Selectors.For Series 3 1971-84 LT76 Gearbox.

Bushing for Front Transfer Output Shaft.For Series 1-3, 1951-84.Proper Bushing with Oil Groove.

Synchro Clutch Assembly for 3rd & 4th Gear 1948-81.Series 1 to 3. Supersedes: GT-239160.Made in Italy.Note: This is a Special Order Item requir...

Set Bolt 1/4" BSF x 13/32" Black Hex Cap. OEMFor Series 2a-3 Reverse Stop Gate, Series 1 Steering Relay, and Swivel Pin.

Knob Gear Lever Black, Pancake Style with Threaded Brass Insert, For Series 1, 2, and 2a to 1971. Excellent quality with the original threaded bras...

Compete set of Shift Knobs for later Series 2A and 3 trucks. (1968 through 1984).Main Gear Lever (Black Push-On type - Round Ball), Transfer Gear C...

Gasket for Front Output Bearing Retainer on Transfer CaseSeries 1-3, 1951-84Supersedes EG-234525

Bell Housing for 2.25L 4 Cylinder Engine to Transmission For Series 3 Gearbox, Clutch Slave on Left-Hand Side. New Old Stock

Stud for Gearbox Brackets on Transfer Case Series 1-3 7/16" Whitworth and 7/16" BSF. Requires Nut BN-2096.

Circlip for Rear Mainshaft Bearing at PTO Cover Series 1-3

Bearing for Rear of Main Shaft in Gearbox.For Series 1-3.

Bearing for Front Output Shaft Series 1-3, 48-84 & 4-Spd V8

Spring for Gear Selector Shaft 1948-84

Spring for Gear Lever Series 1-3 1948-84 OEM. Note: You are purchasing 1, not 10 as shown in the photo

Housing for Series 1-3 Gearbox Gear Lever

Transfer Selector Shaft for 4WD Series 1-3, 1951-84 OEM

Bush Gear Box Selector - 4WD 1951-84 OEM

Distance Tube for Transfer Gear Lever Selector Fork Series 1-3

Bushing for 4-Wheel-Drive Lever.For Series 1-3.Uses Special Bolt GT-540842.

Plunger for Transfer Selector Shaft Series 1-3 1951-84 OEM Note: You are purchasing 1, not 10 as shown in the photo

Brass Sleeve for Speedometer PinionFor Series 1-3, LT76 Gearbox, 1948-84.

Hinge Stop Assembly Reverse Stop Genuine LR 1948-79

Metal Cover for Top of Bell Housing Series 2-3

Hinge Stop Assembly Reverse Gate Assy 1948-79 LR Gen

Bracket Gear Lever for Reverse Stop Springs S1-3 1948-79

Bearing for Primary Pinion (Front of Main Shaft) Gearbox Series 1-3

4WD Selector Rod Series 1-3 1948-84

Mainshaft Distance Piece (Bushing) 1-Piece. Series 1 to 3 Gearbox Suffix A. You can also use the later 2 separate pieces, GT-FRC4076 and GT-FRC4077...