Series 2 2a 3 Transmission

Gearbox and Transfer Case Gasket and Seal Kit For Series 3. Gasket Set with all Seals required for a full tear-down and rebuild. Includes Front/Rea...

Rubber Gasket for Bell Housing Top Cover Plate 1958-84

Stud for Gearbox and Transfer Case 1-3/4" 1948-84

Spring for Gearbox Reverse and Transfer Selector 1948-84

Peg for LT76 Gearbox Mainshaft Series 1-3, 1948-84 For the other Peg, see GT-RTC1979 (linked below).

Handbrake Lever Grommet (Boot) for Series 2 and 2a, 1958-66.Note: Hole for Handbrake Lever is Round. For the later Series 2a/3 Grommet with the Ova...

Round Retaining Plate with 3 Holes for Speedometer Cable. For Series 1 to 2a, (1950-1971). Fits on Speedometer Cable EP-RTC3484, holding it to the ...

Set of 3 Detent Springs for Synchronising Clutch, (Clutch Synchro), Assembly in Gearbox. For Series 1 to 3, 1948-84. 3rd and 4th Gear Synchro. Supe...

Filler Plug for Swivel Housing Series 1-3. Also, for the Transfer Case Oil Level Plug Gearbox Suffix B on; 1/2" BSP.

Sealing Washer O-Ring Side Rocker Cover for Series 1 2.0L 1954-58, Speedometer Pinion Sleeve Series 1-3 to 1984 and Series 2a 2.6L Water Pump. Mayb...

AVM Free Wheeling Manual Locking Hubs 10-SplineFor Series 1 through 3, to 1980 with 10-Spline Hubs.They're Back Baby! Easy to install, even easier ...

Collar for Under Spring of 4WD Lever Series 1-3.

Corteco OEM Oil Seal for Gearbox to Transfer Case Input Shaft.For Series 1-3.

Rubber Gaitor for Overdrive Lever.For the Fairey or Global Roamer Over-Drive on Series 1-3.

Gasket Cork for Flywheel Timing Inspection Cover.For Series 1-3.

Anchor for Transmission Hand Brake Return Spring (on Transfer Case).Series 1 to 3, 1954-84.

Split Ring Retainer for Series Gearbox Layshaft.For Series 1-2a, up to and including Suffix C, 1948-66.

Reverse Switch for Series 3 Stage 1 V8 with the LT95 4-Speed Gearbox and RRC V8 1970-86 with the LT95 4-Speed Gearbox.OEM Intermotor, Made in Spain.

Gearbox and Transfer Case Gasket and Seal Kit For Series 1-2 1948-61 Gasket Set with all Seals required for a full tear-down and rebuild. Includes ...

Set of 3 Replacement Rubber Grommets for Series 1 1953-58. Handbrake, Gear, and Transfer Lever. Note: Handbrake has a Round Hole for Round Shaft an...

Mainshaft Bushing for 2nd Gear For Series 1-3 (This is 1 half of a two piece bushing, used with GT-FRC4077 linked below left) For the original 1 Pi...

Circlip for Gear Lever Series 1-3 1949-84

Mounting Bracket for Gearbox LH Series 2-3

Oil Seal for Gearbox to Transfer Case Input Shaft.For Series 1-3.

Mounting Bracket for Gearbox RH Series 2-3

Drain Plug or Wading Plug, 1/4" BSP Oil Level Plug for Transfer Case, Series 1 to 2a to Gearbox Suff A, (1962). Note some use 1/8" BSP Plug, SC-FTC...

Metal Cover for Top of Bell Housing Series 2-3

Bearing for Primary Pinion (Front of Main Shaft) Gearbox Series 1-3

Snap Ring for 2nd and 3rd Mainshaft Gears. Series 1-3 1948-84.Supersedes GT-6402 or GT-06402.

Gearbox Bearing Kit Series 2a Suffix B through to Series 3 Suffix A. From September of 1963 (when Land Rover changed the gearbox ratios) up to Sept...

Bell Housing to Transmission Gasket S1-3, 48-84

Gear Lever Grommet (Boot) for Series 1, 2, 2A and 3 ('50-'84)

All three Knobs and the Spring for your Series Gear Shift Set. Main Gear Lever (Black Screw-On type with Brass Insert - Pancake), Transfer Gear Cha...

Peg for LT76 Gearbox Mainshaft Series 1-3, 1948-84. For the other Peg, see GT-6405 (linked below). Supersedes GT-09561.

Thrust Washer for High Gear Wheel in Transfer Case.For Series 1 to 3, 1948 to 84.

All three Knobs and the Spring for your Series Gear Shift Set.Main Gear Lever (Black Screw-On type - Pancake), Transfer Gear Change (Red), 4WD/Hi-...