Series 2 2a 3 Transmission

Anchor for Transmission Hand Brake Return Spring (on Transfer Case).Series 1 to 3, 1954-84.

Split Ring Retainer for Series Gearbox Layshaft.For Series 1-2a, up to and including Suffix C, 1948-66.

Gearbox and Transfer Case Gasket and Seal Kit For Series 1-2 1948-61 Gasket Set with all Seals required for a full tear-down and rebuild. Includes ...

Circlip for Gear Lever Series 1-3 1949-84

Mounting Bracket for Gearbox LH Series 2-3

Mounting Bracket for Gearbox RH Series 2-3

Drain Plug or Wading Plug, 1/4" BSP Oil Level Plug for Transfer Case, Series 1 to 2a to Gearbox Suff A, (1962). Note some use 1/8" BSP Plug, SC-FTC...

Metal Cover for Top of Bell Housing Series 2-3

Gear Lever Grommet (Boot) for Series 1, 2, 2A and 3 ('50-'84)

All three Knobs and the Spring for your Series Gear Shift Set. Main Gear Lever (Black Screw-On type with Brass Insert - Pancake), Transfer Gear Cha...

Filler Plug for Swivel Housing Series 1-3. Also, for the Transfer Case Oil Level Plug Gearbox Suffix B on; 1/2" BSP.

Hylomar 101 RTV Silicon Sealant Tube.85 Grams, For Gasketing/Sealing.

Thrust Washer for High Gear Wheel in Transfer Case.For Series 1 to 3, 1948 to 84.

All three Knobs and the Spring for your Series Gear Shift Set.Main Gear Lever (Black Screw-On type - Pancake), Transfer Gear Change (Red), 4WD/Hi-...

Reverse Switch for Series 3 Stage 1 V8 with the LT95 4-Speed Gearbox and RRC V8 1970-86 with the LT95 4-Speed Gearbox.OEM Intermotor, Made in Spain.

Stud for Gearbox Brackets on Transfer Case Series 1-3 7/16" Whitworth and 7/16" BSF. Requires Nut BN-2096.

Set of 3 Replacement Rubber Grommets for Series 1 1953-58. Handbrake, Gear, and Transfer Lever. Note: Handbrake has a Round Hole for Round Shaft an...

Mainshaft Bushing for 2nd Gear For Series 1-3 (This is 1 half of a two piece bushing, used with GT-FRC4077 linked below left) For the original 1 Pi...

Clevis Assembly with Screw and Spring for 4WD Lever.For Series 1-3, 1950-84.You may require the Locknut BN-3819, and the Cotter Pin FS-3958L. Both ...

Seat for Gear Lever 1949-84 Series 1-3

Gasket Cork for PTO Cover Plate on Transfer Case Series 1-3

Retaining Plate for Speedo Pinion Drive.Series 1-3 1950-84.For the 2 Screws that hold this to the Speedometer Sleeve, see FS-2529. For the 3 screws...

Spring for Transfer Lever Selector Fork Series 1-3 1951-84

Oil Seal for Gearbox to Transfer Case Input Shaft.For Series 1-3.

Spring for Gearbox Forward Selectors 1948-84

Bearing for Primary Pinion (Front of Main Shaft) Gearbox Series 1-3

Special Bolt for 4-Wheel-Drive Lever to Housing.For Series 1-3.Supersedes GT-233410.You may also require the Bushing for in the Lever, see GT-230086.

Snap Ring for 2nd and 3rd Mainshaft Gears. Series 1-3 1948-84.Supersedes GT-6402 or GT-06402.

O-Ring Seal for Hi-Lo Transfer Selector Shaft.For Series 1-3.Supersedes GT-265019 and GT-515572.

Transmission Hand Brake Adjuster Unit, Series 2A-3, 1964-84

Bell Housing to Transmission Gasket S1-3, 48-84

Gearbox Bearing Kit for Series 1-2a, Suff A. This is a five piece kit that will fit trucks right from the beginning in 1948 up until 1963. Includes...

Knob for Gear Lever, Black Pancake Style Screw-On. For Series 1, 2, and 2a to 1971. Black "Pancake" shaped shift knob. Good quality, threaded plast...

Bushing for Reverse Gear Series 1-2a 1948-71. Land Rover Genuine NOS. Supersedes GT-56854.

Shim for Speedometer Drive Housing .015 inch. For Series 1-3, 1948-84.

Set of 3 Detent Springs for Synchronising Clutch, (Clutch Synchro), Assembly in Gearbox. For Series 1 to 3, 1948-84. 3rd and 4th Gear Synchro. Supe...

Stud for Inspection Cover on Flywheel Housing Series 1-3 1956-84.

Split Cotter Pin for Tailgate Chain Clevis Pin, Bonnet Prop Rod, or 4WD Selector Lever.Series 1 to 3.Supersedes FS-2389 and FS-3958. 1/16" x 1/2", ...

Peg for LT76 Gearbox Mainshaft Series 1-3, 1948-84. For the other Peg, see GT-6405 (linked below). Supersedes GT-09561.

Compete set of Shift Knobs for later Series 2A and 3 trucks. (1968 through 1984).Main Gear Lever (Black Push-On type - Round Ball), Transfer Gear C...

Gasket for Front Output Bearing Retainer on Transfer CaseSeries 1-3, 1951-84Supersedes EG-234525

Gearbox Cross Member for 109" LWB Chassis Series 2-3Weld-On.Or you could fab up some brackets to make this a bolt-on.Made in Great Britain.

Retaining Plate for Intermediate Shaft in Transfer Case S 1-3

Circlip for Rear Output Shaft Flange of Gearbox Series 1-3

Cover Plate for Series 3 Transfer Case and Series 1-2a PTO Selector. New old stock, some surface rust present.

Bearing for the Front of the Rear Output Shaft, for the High Gear.For Series 1- 3 Transfer Case.If you need the Circlip, see GT-90217526.

Housing for Series 1-3 Gearbox Gear Lever

Bushing for 4-Wheel-Drive Lever.For Series 1-3.Uses Special Bolt GT-540842.