Series 2 2a 3 Transmission

Spring for Gearbox Forward Selectors 1948-84

Bearing for Primary Pinion (Front of Main Shaft) Gearbox Series 1-3

Special Bolt for 4-Wheel-Drive Lever to Housing.For Series 1-3.Supersedes GT-233410.You may also require the Bushing for in the Lever, see GT-230086.

Snap Ring for 2nd and 3rd Mainshaft Gears. Series 1-3 1948-84.Supersedes GT-6402 or GT-06402.

O-Ring Seal for Hi-Lo Transfer Selector Shaft.For Series 1-3.Supersedes GT-265019 and GT-515572.

Transmission Hand Brake Adjuster Unit, Series 2A-3, 1964-84

Bell Housing to Transmission Gasket S1-3, 48-84

Gearbox Bearing Kit for Series 1-2a, Suff A. This is a five piece kit that will fit trucks right from the beginning in 1948 up until 1963. Includes...

Knob for Gear Lever, Black Pancake Style Screw-On. For Series 1, 2, and 2a to 1971. Black "Pancake" shaped shift knob. Good quality, threaded plast...

Bushing for Reverse Gear Series 1-2a 1948-71. Land Rover Genuine NOS. Supersedes GT-56854.

Shim for Speedometer Drive Housing .015 inch. For Series 1-3, 1948-84.

Set of 3 Detent Springs for Synchronising Clutch, (Clutch Synchro), Assembly in Gearbox. For Series 1 to 3, 1948-84. 3rd and 4th Gear Synchro. Supe...

Stud for Inspection Cover on Flywheel Housing Series 1-3 1956-84.

Split Cotter Pin for Tailgate Chain Clevis Pin, Bonnet Prop Rod, or 4WD Selector Lever.Series 1 to 3.Supersedes FS-2389 and FS-3958. 1/16" x 1/2", ...

Peg for LT76 Gearbox Mainshaft Series 1-3, 1948-84. For the other Peg, see GT-6405 (linked below). Supersedes GT-09561.

Compete set of Shift Knobs for later Series 2A and 3 trucks. (1968 through 1984).Main Gear Lever (Black Push-On type - Round Ball), Transfer Gear C...

Gasket for Front Output Bearing Retainer on Transfer CaseSeries 1-3, 1951-84Supersedes EG-234525

Gearbox Cross Member for 109" LWB Chassis Series 2-3Weld-On.Or you could fab up some brackets to make this a bolt-on.Made in Great Britain.

Retaining Plate for Intermediate Shaft in Transfer Case S 1-3

Circlip for Rear Output Shaft Flange of Gearbox Series 1-3

Cover Plate for Series 3 Transfer Case and Series 1-2a PTO Selector. New old stock, some surface rust present.

Bearing for the Front of the Rear Output Shaft, for the High Gear.For Series 1- 3 Transfer Case.If you need the Circlip, see GT-90217526.

Housing for Series 1-3 Gearbox Gear Lever

Bushing for 4-Wheel-Drive Lever.For Series 1-3.Uses Special Bolt GT-540842.

Special Bolt for 4WD Selector Shaft Series 1-3

Retainer for Transfer Lever Rubber Grommet.Series 1-3 1954-84.

Hinge Stop Assembly Reverse Stop Genuine LR 1948-79

4 Wheel Drive Selector Rod for Series 1-3 1948-84.Note: This Uses 2x BN-3819 1/4" BSF Nuts, GT-561221 Spring, GT-215808 Clevis. If this is for an e...

Mainshaft Distance Piece (Bushing) 1-Piece. Series 1 to 3 Gearbox Suffix A. You can also use the later 2 separate pieces, GT-FRC4076 and GT-FRC4077...

Roller Bearing for Gearbox Mainshaft Front S1-3, & LT85

Circlip for Front Output Bearing 1948-84, & LT95 Frt O/P Shft

Bearing for Rear of Rear Output Shaft in the Transfer CaseFor Series1-3, NTN OEM.

Mainshaft Bushing for 3rd Gear For Series 1-3 (This is 1 half of a two piece bushing, used with GT-FRC4076 linked below left) For the original 1 Pi...

Gasket Cork for Transfer Case Inspection Plate Series 1-3. Supercedes part number 219995.

Thrust Washer 0.125", (3.18mmf), for 3rd Gear Series 1-3.

Gearbox Bearing Kit Series 2a Suffix B through to Series 3 Suffix A. From September of 1963 (when Land Rover changed the gearbox ratios) up to Sept...