Service & Hardware

Catch Assembly RH Cab Rear Window and Hard Top Sides

Catch Assembly Latch LH Cab Rear Window and Hard Top Sides

Edge Clip for Interior Trim and Various - Defender OEM

Support for Door Striker Left Hand Series 109", and all Defenders, OEM. For the Right Hand Support Bracket see BP-MWC1736.  

Nut Plate for Defender Roof, (6 Required - Front of Roof to Windscreen), or Bench Seat Belts Series 1-3.Supersedes BP-334177 and BP-MTC3203.Note: Y...

Bracket for Sill Panel Mount Defender 90/110/130

Nut Plate for Rear Body to Chassis Mount Series 1 to 3 and Defender to 2002. OEM. 5 Typically Required. Requires 2x Split Rivet RV-RB610082 and 2x ...

Center Catch for Seat Base Lids 90/110 and Various OEM

Clip for Bonnet Prop Rod Solid Defender to WA159806 OEM You are purchasing 1, not 5 as shown in the photo

Bracket for Side Panel to Tub, Rear.For Series and Defender.Land Rover Genuine.Supersedes BP-338552, BP-LR010907.

These are the fasteners necessary for fitting the bumper end caps (CP-DPT100070) on the Defender. You'll need four per cap, so eight in total. The...

Stainless Steel Front Vent Hinge Pin Kit (Set of 4) Notes: For Welded On Hinges. 4 Required per Bulkhead. For Series 2-3 and Most Defenders to 2007...

Special Stud for Mounting Hard Top Side Panels on Series 2-3 109" and Defender 110.Supersedes BP-338740 and BP-MRC9833.For the Stud used on Series ...

Bonnet Striker Pin with Spring Defender 1986 on

Hook for Top Drain Channel for Defender 90/110 from '86 OEM

Firtree Fastener White for Headliner Defender from 1988 OEM

Rivet Spat for Wheel Arches Defender and Various UsesFor a Package of 10, see BP-AFU1075-10. For Re-Usable Rivets see BP-AFU1075RU10.

Spring Clip for Tools behind Front Seats Series 1-3.For tools, like the hand crank, with a diameter up to 5/8".You'll need a rivet for installation...

Spring for Bonnet Catch RRC, D1, 90/110

Check Strap Bracket Front Door Series 3, 90/110 Rear 82-89

Hinge for Bonnet Right Hand Genuine Land Rover Galvanized Series 3 1972-84 For Left-Hand Hinge, see BP-345854 (linked below).

Hinge Bushing for Hood (Bonnet),For Series 2a-3, 1972 on, Defender through to 2016,

Turnbuckle for Seat Base Locker Lids for Series1-3

Front Vent Hinge Pin for Welded On Hinges 4 Typically Required. Series 2-3 and Defender up to 1998. OEM. For a Stainless Steel Pin Kit see BP-DA117...

Nut Flanged Metric M8 for V8 Y-Pipe to Manifold, and Turbo-Manifold Diesel.For Discovery 2 and Range Rover.Supersedes BN-ERR4245.

Washer Flat for Hard Top Side Panels

Washer Spring Lock 7/16" Zinc for Door Top Bolts. OEM You are purchasing 1, not 50 as shown in the photo.

Washer Spring Lock 3/8" Washer Zinc Multiple uses

Washer Spring Lock 5/16" Washer Zinc

Washer Spring Lock 1/4" Washer Zinc.Supersedes BN-3074. Note: You are purchasing 1, not 10 as shown in the photo.

Washer Spring Lock 10mm Light-Duty Various Uses OEM.For Defender Rear Shocks. Note: You are purchasing 1, not 10 as shown in the photo.

Washer Spring Lock 12mm Zinc for Various Uses OEM. You are purchasing 1, not 10 as shown in the photo.

Washer Spring Lock M10 White Zinc Medium Duty Various Uses.For Front Mount of Defender Fuel Tank, and Engine Mounts EM-STC434.

Washer Spring Lock 8mm Various Uses OEM. You are purchasing 1, not 10 as shown in the photo.

Washer Spring Lock Metric M6 for Various Uses

Washer Flat Plain 10mm Various Uses OEM. You are purchasing 1, not 10 as shown in the photo.

Washer Lock External Tooth 5/16' Zinc. Note: You are purchasing 1, not 10 as shown in the photo.

Washer Flat 13mm x 5mm for Floor Panels to Footwells. OEM. Note you are purchasing 1, not 10 as shown in the photo.

Washer Flat Zinc M16 for Various Uses, Anti-Sway Bar OEM. You are purchasing 1, not 10 as shown in the photo.

Washer Flat 12mm for Tie-Rod Ends OEM. You are purchasing 1, not 10 as shown in the photo.

Washer Flat M10 Zinc Various Uses Oversize. 25mm OD 10.5mm ID 2mm Thick. Note: You are purchasing 1, not 20 as shown in the photo.

Washer Flat Plain 8mm for Various Uses OEM.Note: You are purchasing 1, not 10 as shown in the photo.

Washer Flat 5mm ID, 12mm OD, Zinc, Various Uses.Note: You are purchasing 1, not 10 as shown in the photo.

Washer Flat Various Uses 5/8"ID x 1-1/8"OD.For Series 3 LHD Hand Brake Lever.

Washer Flat 1/2" (12mm) for Defender Bulkhead to Frame (2 required per bolt).Also used for Antiluce Pins.

Washer Flat 1/4" SAE ID 7/16"OD Zinc for Steering Clamps. OEM. Note: You are purchasing 1, not 10 as shown in the photo.

Washer Flat M12 for Series or Defender Bulkhead to Chassis and Antiluce Tailgate Pins, Metric. Yellow Zinc.

Washer Flat Plain Metric M10 10mm ID 20mm OD Zinc.For Defender Front Anti-Sway Bar and Various other uses.