Series Body Hardware

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Nylon Lock Nut for Shackle Pins 9/16" UNF

Set of 3 Replacement Rubber Grommets for Series 2a-3 1967-84.Handbrake, Gear, and Transfer Lever.Handbrake has Oval Hole. This set can work for ear...

Shackle Bolt for Front-End of Front Spring and Front-End of Rear Spring 9/16" UNF For 88" and 109"

Floor Screws and Spire Nuts. Package of 10x FS-320045 and 10x FS-302532

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.

Bolts, Nuts and Washers for the Bulkhead to the Chassis.Fits Series 1 to 3, 1948-84.

Spring into action with this shifter spring for 4WD Hi-Low Selector Lever. For Series 1-3 trucks from 1950 through to the end of the run in 1984.

Castle Nut for Halfshaft, Output Shaft and Differential Pinion.Requires Cotter Pin AD-PS608101L and Flat Washer AD-571922.

Bolt for Rear Propshaft both ends, and Front Propshaft to Differential.Series 1, 1948-58, Requires 8 for the Front and 1950-58 Requires 4 for the R...

Bolt 1/4" UNFx 2-1/2" for Thermostat Housing.For Series 2-3, 1958 on. 3 Typically Required.

Pop-Rivet Aluminium. 3/16"x1/2" Maximum Clinch 9/32" Sealed EndPackage of 10

Stainless Steel Front Vent Hinge Pin Kit (Set of 4) Notes: For Welded On Hinges. 4 Required per Bulkhead. For Series 2-3 and Most Defenders to 2007...

Bleed Screw for Wheel Cylinders, Series 1-3 1954-84, and 2/2a Clutch Slave.

Hub Spanner Wrench for Hub Locking Nut 2-1/16" 52mm. For locknut FRC8700.

Rubber Seal for Fuel Sender UnitFor 109 Station Wagon, Defender Side and Rear Tank to 1998.For the Twist Clamp, see EF-ARA1501L.

Mounting Pad between Rear Tub Floor and Cross-Braces6 Required for Series 1-3 86"/88" and Defender 90 8 Required for Series 2-3 109" Station Wagon ...

Set of 3 Replacement Rubber Grommets for Series 2/2a 1958-66. Handbrake, Gear, & Transfer Lever. This Handbrake grommet does not fit Series 1 1...

Set of 4 Stainless Steel Door Hinge Pin Kits For Series 2-2a Front Doors or Middle Row Doors. Does 4 Hinges.

Shackle Bolt for Rear of Rear Spring - 9/16 UNF 88/107/109

Clamp Ring for Fuel Sender For 109 Station Wagon, Defender Side and Rear Tank to 1998. For Rubber Seal, see EF-ARA1502L (linked below).

Fuel Tank Fitting Kit for 88/109R Side Fuel Tank (552174)

Battery Hold-Down J-Clamp Kit

Rubber Grommet for Brake Line P-Clamps 3/16"-1/4"

Nut 1/4" BSF for Various Uses. For the Swivel Lock stop Bott, Yellow 4WD Knob, 4WD Clevis Assembly, Transfer Case Bottom Cover, Series 1 2.0L Intak...

Special Stud for Swivel Housing 7/16"BSF Series 2a-3 This Stud has a thicker non-threaded center. 4 Required for Top, February 1962-66. 2 required ...

Spring Clip for Tools behind Front Seats Series 1-3.For tools, like the hand crank, with a diameter up to 5/8".You'll need a rivet for installation...

P-Clamp for Brake Lines.For Series 1-3 Single or Dual Line 3/16 and 1/4" Pipes.Supersedes BC-50640.

Starting Handle for Series Engines, (tool for timing) 1948-84.Make certain that your engine has the starting dog on the crankshaft.You might need t...

Wings to Breakfast Radiator Panel Stud Plate Kit For Series 2-3. Galvanized Plates with Stainless Steel Studs, Nuts and Washers.Includes 2x BP-MRC5...

Stainless Steel Antiluce Pin Kit for TailgateFor Series and Defender.Shiny Pair.

Rubber Washer Seal for Sliding Window Catch on Station Wagon Hard Top Side Panels.For Series 2-3.2 Required per Catch.

Shackle Bolt for Rear of Front Spring - 9/16" UNF 88/109

Clip for Speedometer Cable and Other Applications.Series 1-3.

Floor Screws Series 1-3 and Various Uses.Package of 10.

Bolt 7/16"UNF x 2.25" Grade 8 Yellow Zinc.For Upper or Lower Arm to Steering Relay.Series 2 to 3, 1958-84.Supersedes BN-215390, (BSF) and BN-256465...