Series Body Hardware

Stainless Steel Bolt Kit for Bonnet Hinges.For Series 3 and Defender.

Rope Tie-Down (U-shape) on Rear Tub for Canvas Top.Zinc.For Series 1-3 and Defender. Requires 2 Rivets, RV-RU612373.

Hinge to Bulkhead Screw 1.5" Long for Series 3 and Defender Hinge, OEMThis is the shorter screw that holds the Hinge to the Bulkhead. For the longe...

Bolt Kit for Swivel Ball Flange to Axle.This is an Axle Set; does both Left and Right Sides.Series 1-3, 1948-84.

Bolt Kit for Seal Retainer to Swivel Hub.This is an Axle Set; does both Left and Right Hand Sides.Series 1 to 3, 1948-84.

Bolt for Transfer Boot Retainer Bracket to Floor OEM.For Series 1-3, and Defender to 1986.

Bolt 1/4" UNFx 2-1/2" for Thermostat Housing.For Series 2-3, 1958 on. 3 Typically Required.

These top hat supports are for the underside of your bonnet on a Series 2 and 3.They are made from 1.2mm thick zintec coated mild steel, which are ...

Bolt for Bonnet Spare Wheel Carrier Mounting.1/2" BSF x 3" Long. Works with Clamp BP-347262.

Staple for Hood Strap on Rear Tub and on Windscreen Rail.For Series and Defender.You are Purchasing 1, not 10 as shown in photo.

Chain Galvanized for Tailgate 28mm 20-Links Series/Defender. OEM.

Nut 7/16" BSF for Various Uses For Series 1-3 Gearbox Bracket Mounts, Steering Levers Supersedes BN-594104. For Nyloc Version, see BN-251323.

Screw 2BA x 1" Slotted Round Head OEM For BG-304125 Buffer, TS-MXC4657 (348430) Stud and Various other usesFor the matching 2BA nut, see FS-RTC608.

Plastic Lokut Nut Floor to Footwell & Other Uses (RTC3744) OEM Please note, you are purchasing 1, not 10 like shown in the photo.

Hinge for Bonnet Left Hand Genuine Land Rover Galvanized Series 3 1972-84 For Right-Hand Hinge, see BP-345853.

Hinge for Bonnet Right Hand Genuine Land Rover Galvanized Series 3 1972-84 For Left-Hand Hinge, see BP-345854.

Set of 2 Stainless Steel Door Hinge Pin Kits For Series 2-2a, 1958-71. Does One Door. Front, Middle, or Rear 2-Hinge Safari Door.

Spire Nuts for Floor Screws and Other Uses Package of 10

Set of 3 Replacement Rubber Grommets for Series 1 1953-58. Handbrake, Gear, and Transfer Lever. Note: Handbrake has a Round Hole for Round Shaft an...

Set of 3 Stainless Steel Door Hinge Pin Kits For Series 2-3 or Defender 3-Hinge Rear Safari Door

Stud Plate for Sill Channel to Bulkhead Series 2 and 3 You are purchasing 1 Stud Plate

Bolt ACME for Front Wing to Bulkhead S 2-3, 90/110 Zinc

Rubber Washer Seal for Sliding Window Catch on Station Wagon Hard Top Side Panels.For Series 2-3.

Rubber Buffer (Puck) for Spare Wheel on Bonnet Kit of 4. Series 1-3.

Brake Drum Screws Series 1-3 1948-1984 Each.For a Package of 10, see BB-1510-10.

Hub Spanner Wrench for Hub Locking Nut 2-1/16" 52mm. For locknut FRC8700

Floor Screw Acme Thread Series 1-3 and DefenderFor a Package of 10 Floor Screws see FS-320045-10, or a Package of 10 Screws and 10 Spire Nuts, see ...

Copper Washer for 7/16" Brake Hose BC-219824 Series 1 1948-53.Also used on Series 2/2a Banjo Bolt for Brake Master Cylinder LHD, and with Brake/Clu...

Bolt for Seat Belt at Seat Box Anchor Bracket.For Series 2a and 3. Fastens the Seat Belt to the Lower Corner Brackets, SB-345100/1.Note: Typically ...

Washer Special for Clutch Clevis Pin & Other Uses.Supersedes CC-10882.

Split Cotter Pin 3/64" x 3/4" for Series 1 Solex Carburetor, Oil Strainer, Door Check Strap Clevis Pin, RRC Accelerator Pedal and Various Other Use...

Seat Belt Anchor Bracket Front Lower Right and Left Hand, PAIR.Hot-Dip Galvanized. For Series 1-3, and Defender.

Floor Screws Series 1-3 and Various Uses.Package of 10.

Stainless Steel Screw for Name Plate and Grill.#10 x 3/4" Slotted Pan Head Type B Point.For Series 2 and 2a.

Screw Fixing Plastic Grill Series 3

Washer Lock for 2BA Screws and TS-MSC4657 Studs and Various Other Uses You are purchasing 1, not 10 as shown in the photo.

Washer Special for Mounting Hard Top Side Panels.For Series 2-3 Station Wagons and Defender 110 Station Wagons.Supersedes BN-332293.

Washer Flat for Hard Top Side Panels and Various Uses.Series and Defender.

Bolt Set Hex Cap 5/16" UNC x 5/8" for Various Uses.For Series 2.25L Heat Shield to Manifold.

Pop Rivet 1/8" Diameter x 1/4" Long, Aluminium with Aluminium Mandrel.For Various Uses on Series, Defenders, Discovery 1, and RRC.

Bolt 1/4" BSF x 5/8" for Seal Retainer Plate to Swivel Hub OEM Series 1-3 You are purchasing 1, not 10 as shown in the photo

Bolt for Series 3 Windscreen to Bulkhead.UNF, 1971-80. Later uses the Metric Bolt, BN-MRC6074, which is no longer available.

Locker Plate for Spring U-Bolts (For 2.5" Narrow Springs).For Series 1 to 2a, 1952-64 with the Early Narrow 2.5" Wide Leaf Springs.New Old Stock - ...

Clamp for Bonnet Spare Wheel Carrier Series 1-31/2" Hole for Bolt BN-345779.

Hose Clamp 3/8" - 9/16" Diameter x 5/16" Bandwidth, All Stainless, Various Uses.Used for In-Line Fuel Filters, etc.Supersedes HC-AAU1979, HC-PYC101...

Bolt 7/16"UNF x 2.25" Grade 8 Yellow Zinc.For Upper or Lower Arm to Steering Relay.Series 2 to 3, 1958-84.

Nut Nylon Lock 7/16" UNF Grade 8.For Upper or Lower Steering Arms to Relay, and Shock Bolts.Series 2 to 3, 1958-84.