Series Body Hardware

Door Lock Cylinder Barrels and Keys, 2 Sets, with Matched Keys.For Series 3 Anti-Burst Handles, Defender Push-Button Handles and Rear Safari Door t...

Bonnet Catch Assembly for Series 2-3. OEM. Not for 109 V8 For the Bonnet Striker Plate see BP-332400 (linked below).

Nut 2BA Thread for Accelerator Rod Ball Joints and Various Other Uses.Supersedes FS-2247 and FS-3823.Note: You are purchasing 1, not 10 as shown in...

Stud 7/16" BSF for Bottom of Swivel Housing Series 2a-34 Required on Top from Feb 1962 to '66, or use later alternative Bolt, BN-237357.2 required ...

Stud for Gearbox Brackets on Transfer Case Series 1-3 7/16" Whitworth and 7/16" BSF. Requires Nut BN-2096.

Plastic Lokut Nut Floor to Footwell and Other Uses OEM, Made in the UK.Please note, you are purchasing 1, not 10 as shown in the photo.Supersedes F...

Screw for Fuel Sender Unit 3BAx3/8" 6 Required Note: These only fit Original Tanks. New Fuel Tanks may require Metric M4x16 or SAE 6-40.

Hinge for Bonnet Left Hand Genuine Land Rover Galvanized Series 3 1972-84 For Right-Hand Hinge, see BP-345853 (linked below).

Hinge for Bonnet Right Hand Genuine Land Rover Galvanized Series 3 1972-84 For Left-Hand Hinge, see BP-345854 (linked below).

Seat Box Hasp for Locker Lid Series 2-3 1958-84 Short Hasp

Door Lock Cylinder Barrels and Keys, 4 Sets, with 8 Matching Keys.For Series 3 Anti-Burst Handles, Defender Push-Button Handles and Rear Safari Doo...

Nut Plate for Defender Roof, (6 Required - Front of Roof to Windscreen), or Bench Seat Belts Series 1-3.Supersedes BP-334177 and BP-MTC3203.Note: Y...

Door Lock Cylinder Barrels and Keys, 3 Sets, with 6 Matching Keys.For Series 3 Anti-Burst Handles, Defender Push-Button Handles and Rear Safari Doo...

Set of 3 Stainless Steel Door Hinge Pin Kits For Series 2-3 or Defender 3-Hinge Rear Safari Door

Bearing Grease 20ml Sachet for Hub Bearings

White Canvas Strip Only, Series 1-3, 1948-1984, (White Canvas).For Breakfast (Front Grill), under Bonnet (Hood).You will need fasteners FS-338380 (...

Brake Hose Nut Metric 10mm Zinc Series 3, June 1980-84

Bolt 7/16" UNF 7 1/4" for Shock Absorber Rear 109, 1958-84. OEM.

Special Set Bolt for Flywheel to Crank 2.25L 3-Bearing Engines and the 2.6L, Series 2-3.8 Typically Required. For the Locker Plates, see CC-534098.

Rear Cross-Member Plates and Bolts Fastening Kit for Series and Defender to 2002. Includes 5x BP-YRM097A, (BP-MRC8736), Aluminium Nut Plates, 10x S...

Bolt 1/2" UNF for Bulkhead to Frame.For Series 1 to 3, 1948-84. OEM.Supersedes BN-300827 and BN-303907, (BSF Versions of the same size bolt), no lo...

Bolt Kit for Series 2, 2a and 3, 1969 to 84, Right and Left Hand Mud Shield Splash Guards. Correct Fasteners for Doing Both Sides for LHD and RHD. ...

Stud for Inspection Cover on Flywheel Housing Series 1-3 1956-84.

Special Bolt Long BSF for Rover Differential in Axle Case.Series 1-2a.3/8"BSFx 1-3/4" Hex Fully-Threaded. Typically 6 Required.For the Matching BSF...

Split Cotter Pin for Tailgate Chain Clevis Pin, Bonnet Prop Rod, or 4WD Selector Lever.Series 1 to 3.Supersedes FS-2389 and FS-3958. 1/16" x 1/2", ...

Screw Fixing Plastic Grill Series 3

Washer Special for Mounting Hard Top Side Panels.For Series 2-3 Station Wagons and Defender 110 Station Wagons.Supersedes BN-332293.

Pop Rivet 1/8" Diameter x 1/4" Long, Aluminium with Aluminium Mandrel.For Various Uses on Series, Defenders, Discovery 1, and RRC.

Clamp for Bonnet Spare Wheel Carrier Series 1-31/2" Hole for Bolt BN-345779 (linked below).

Hose Clamp 3/8" - 9/16" Diameter x 5/16" Bandwidth, All Stainless, Various Uses.Used for In-Line Fuel Filters, etc.Supersedes HC-AAU1979, HC-PYC101...

Bolt for Transfer Boot Retainer Bracket to Floor OEM.For Series 1-3, and Defender to 1986.

Stud for the Intake Manifold to the Exhaust Manifold,For the 2.25L Gas Engine, Series 2, 2a and 3.4 Required. For a Complete Kit with Bolts, Nuts, ...

Special Stud Long UNF for Rover Differential in Axle Case.This is the 3/8" UNF x 1-3/4" Long Push-Through Stud, considered the "Longer" Stud. 6 Typ...

Special Stud Long UNF for Rover Differential in Axle Case.This is the 3/8" UNF x 1-1/4" Long Push-Through Stud, considered the "Shorter" Stud. 4 Ty...

These top hat supports are for the underside of your bonnet on a Series 2 and 3.They are made from 1.2mm thick zintec coated mild steel, which are ...

Bolt 3/8" BSF by 1" Long.Front Stub Axle to Swivel Hub, Front Brake Plate to Swivel, Set Bolt for Rover Differential Crown Wheel.

Chain Galvanized for Tailgate 28mm 20-Links Series/Defender. OEM.

Clip for Plastic Grill on Series 32 Required.

Bonnet Striker Plate for Series 2-3.For the Bonnet Catch Assembly, see BP-332401.

Screw 2BA x 1" Slotted Round Head OEM For BG-304125 Buffer, TS-MXC4657 (348430) Stud and Various other usesFor the matching 2BA nut, see FS-RTC608.

Door Lock Cylinder Barrels and Keys, 5 Sets, with 10 Matching Keys.For Series 3 Anti-Burst Handles, Defender Push-Button Handles and Rear Safari Do...

Front Vent Hinge Pin for Welded On Hinges 4 Typically Required. Series 2-3 and Defender up to 1998. OEM. For a Stainless Steel Pin Kit see BP-DA117...

Cylinder Head Bolt for 2.25L Series 2-3 Engine. OEM. Note: You are purchasing 1, not 10 as shown in the photo.

Rubber Buffer (Puck) for Spare Wheel on Bonnet Kit of 4. Series 1-3.

Bolt Kit Rear Stub Axles to Rover Axle S2/2a (Axle Set)

Washer Double Spring 9/16" for Tailgate Hinge. OEM. You are purchasing 1, not 10 like shown in the photo.

Bracket for Side Panel to Tub, Front.For Series and Defender.Supersedes BP-338554.