Series Body Hardware

Swivel Hub Grease Sachet, 370 grams, sufficient for 1 swivel hub. Perfect solution for those leaky swivels. Not recommended if you wade through wat...

Nylon Lock Nut for Shackle Pins 9/16" UNF

Set of 3 Replacement Rubber Grommets for Series 2a-3 1967-84.Handbrake, Gear, and Transfer Lever.Handbrake has Oval Hole. This set can work for ear...

Shackle Bolt for Front-End of Front Spring and Front-End of Rear Spring 9/16" UNF For 88" and 109"

Floor Screws and Spire Nuts. Package of 10x FS-320045 and 10x FS-302532

Copper Washer 3/8" for Brake or Clutch HoseFor Series 1-3, 1954-1984.

Bolts, Nuts and Washers for the Bulkhead to the Chassis.Fits Series 1 to 3, 1948-84.

Castle Nut for Halfshaft, Output Shaft and Differential Pinion.Requires Cotter Pin AD-PS608101L and Flat Washer AD-571922.

Spring into action with this shifter spring for 4WD Hi-Low Selector Lever. For Series 1-3 trucks from 1950 through to the end of the run in 1984.

Bolt for Rear Propshaft both ends, and Front Propshaft to Differential.Series 1, 1948-58, Requires 8 for the Front and 1950-58 Requires 4 for the R...

Rubber Seal for Fuel Sender UnitFor 109 Station Wagon, Defender Side and Rear Tank to 1998.For the Twist Clamp, see EF-ARA1501L.

Pop-Rivet Aluminium. 3/16"x1/2" Maximum Clinch 9/32" Sealed EndPackage of 10

Mounting Pad between Rear Tub Floor and Cross-Braces6 Required for Series 1-3 86"/88" and Defender 90 8 Required for Series 2-3 109" Station Wagon ...

Bleed Screw for Wheel Cylinders, Series 1-3 1954-84, and 2/2a Clutch Slave.

Hub Spanner Wrench for Hub Locking Nut 2-1/16" 52mm. For locknut FRC8700.

Bolt 1/4" UNFx 2-1/2" for Thermostat Housing.For Series 2-3, 1958 on. 3 Typically Required.

Stainless Steel Front Vent Hinge Pin Kit (Set of 4) Notes: For Welded On Hinges. 4 Required per Bulkhead. For Series 2-3 and Most Defenders to 2007...

Set of 3 Replacement Rubber Grommets for Series 2/2a 1958-66. Handbrake, Gear, & Transfer Lever. This Handbrake grommet does not fit Series 1 1...

Set of 4 Stainless Steel Door Hinge Pin Kits For Series 2-2a Front Doors or Middle Row Doors. Does 4 Hinges.

Rubber Grommet for Brake Line P-Clamps 3/16"-1/4"

Clamp Ring for Fuel Sender For 109 Station Wagon, Defender Side and Rear Tank to 1998. For Rubber Seal, see EF-ARA1502L (linked below).

Fuel Tank Fitting Kit for 88/109R Side Fuel Tank (552174)

Battery Hold-Down J-Clamp Kit

Shackle Bolt for Rear of Rear Spring - 9/16 UNF 88/107/109

P-Clamp for Brake Lines.For Series 1-3 Single or Dual Line 3/16 and 1/4" Pipes.Supersedes BC-50640.

Nut 1/4" BSF for Various Uses. For the Swivel Lock stop Bott, Yellow 4WD Knob, 4WD Clevis Assembly, Transfer Case Bottom Cover, Series 1 2.0L Intak...

Special Stud for Swivel Housing 7/16"BSF Series 2a-3 This Stud has a thicker non-threaded center. 4 Required for Top, February 1962-66. 2 required ...

Stainless Steel Antiluce Pin Kit for TailgateFor Series and Defender.Shiny Pair.

Spring Clip for Tools behind Front Seats Series 1-3.For tools, like the hand crank, with a diameter up to 5/8".You'll need a rivet for installation...

Shackle Bolt for Rear of Front Spring - 9/16" UNF 88/109

Starting Handle for Series Engines, (tool for timing) 1948-84.Make certain that your engine has the starting dog on the crankshaft.You might need t...

Hylomar 101 RTV Silicon Sealant Tube.85 Grams, For Gasketing/Sealing.

Floor Screws Series 1-3 and Various Uses.Package of 10.

Bolt 3/8" BSF x 1 19/32" for Drive Flange Member. OEM. These bolt both the front and the rear drive flanges to the hub assemblies. You will need s...

Stainless Steel Bolt Kit for Bonnet Hinges.For Series 3 and Defender.

Staple for Hood Strap on Rear Tub and on Windscreen Rail.For Series and Defender.You are Purchasing 1, not 10 as shown in photo.

Spring Clip for Tools behind Front Seats Series 1-3, Extra-Large.Holds tools with a diameter up to 1"; just a little larger than the standard one.Y...

Wings to Breakfast Radiator Panel Stud Plate Kit For Series 2-3. Galvanized Plates with Stainless Steel Studs, Nuts and Washers.Includes 2x BP-MRC5...

Nut 7/16" BSF for Various Uses. OEM.For Series 1-3 Gearbox Bracket Mounts, Steering Levers Supersedes BN-594104. For Nyloc Version, see BN-251323. ...

Bolt ACME for Front Wing to Bulkhead S 2-3, 90/110 Zinc. OEM.

Rubber Washer Seal for Sliding Window Catch on Station Wagon Hard Top Side Panels.For Series 2-3.2 Required per Catch.

Automec Small Pipe Bender Tool for 3/16" Copper-Nickel Pipe Great tool for making the right bends when installing any of the 3/16" kits.

Dust Cap for Wheel Cylinder or Clutch Slave Bleed Screw pn: BB-556508. You are purchasing 1, not 10 as shown in the photo.

Clip for Speedometer Cable and Other Applications.Series 1-3.

Bolt 1/4" BSF x 1" Lockstop Set Bolt for Swivel Hub S1-3 OEM

Front Wings to Bulkhead Fastener Kit.For Series 2, 2a and 3, and Defender.

Bolt 7/16"UNF x 2.25" Grade 8 Yellow Zinc.For Upper or Lower Arm to Steering Relay.Series 2 to 3, 1958-84.Supersedes BN-215390, (BSF) and BN-256465...

Rear Cross-Member Bolt Kit Stainless Steel.Metric, For Series and Defender.To bolt the rear tub to rear body mounting bracket, (Puma style), and to...